MEHMET AKİF KUNT

Dr. MEHMET AKİF KUNT


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 January 2026 in Engineering Perspective
Verified
Journal Article
Closed access
AÇAhmet Çelik
Ahmet Çelik
MKMEHMET AKİF KUNT
MEHMET AKİF KUNT
Machine learning algorithms are often used to mathematically establish relationships between data sets. Successful results have been achieved in performance, production, consumption, fault, and wear prediction applications using learning algorithms. The high testing costs of Homogeneous Charge Compression Ignition (HCCI) engines, the determination of efficient operating ranges, and the challenges of performance prediction in untested regions have recently made the use of artificial intelligence technologies increasingly popular. In this study, a dataset (805 data) was created by varying the λ value in a single-cylinder HCCI engine (Ricardo Hydra) and conducting performance measurements at different engine speeds. Based on the input values of Compression Ratio, RON (Research Octane Number), Intake Air Temperature (K), Engine Speed (rpm), and Lambda (λ) within the dataset, the output variables IMEP(Bar), Effective Torque, Indicated Thermal Efficiency, and COVimep (%) were predicted. In this study, a prediction model was developed using the AdaBoost and Tree machine learning algorithms. The experimental results demonstrated that the AdaBoost algorithm achieved the highest accuracy in predicting IMEP (Bar) output values and the lowest error rates in predicting Indicated Thermal Efficiency output values. The highest performance was obtained with an R metric a value of 9.57×10-1, while the lowest error rates were calculated as 2.89×10-4 for the MSE error metric, 1.70×10-2 for the RMSE error metric, 1.30×10-2 for the MAE error metric, and 4.10×10-2 for the MAPE error metric. The results indicate that high-accuracy predictions can be made using the proposed model.

14 November 2017 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Verified
Journal Article
Closed access
MKMEHMET AKİF KUNT
MEHMET AKİF KUNT
Almost 70% of heat power produced by pistons in internal combustion engines is lost due to exhaust and cooling. In the course of the heating process, 25% of useful energy transfers to the exit shaft. There have been a lot of studies on recycling waste heat of internal combustion engines, especially on cooling and exhaust systems. A thermoelectric generator is an important way to recycle waste energy in exhaust systems of internal combustion engines. In this study, an air-cooled thermoelectric generator was designed to recycle waste heat energy in exhaust systems of internal combustion engines and its performance was tested. Waste heat recycling tests were conducted by measuring voltage, current, and power values under different thermal conditions depending on the change in load resistance. The results obtained were compared with the results of analyses and experiments. Maximum voltage value at RI = 45Ω load resistance was obtained as 11.03 V (experiment) and 11.22 V (analysis), and maximum current value at RI = 5Ω load resistance as 0.42 A (experiment) at Th = 250°C, Δ T = 40°C.

30 September 2021 in International Journal of Automotive Science And Technology
Verified
Journal Article
Closed access
PDF file
MKMEHMET AKİF KUNT
MEHMET AKİF KUNT
Selection of transmission systems of motor vehicles used on highways is high-ly important in terms of fuel consumption and vehicle efficiency. In this study, effect of using 3 different gearboxes in a passenger car (automatic gearbox, CVT gearbox and manuel gearbox) on driveline friction losses and engine operation interval by means of GT SUITE vehicle modelling programme. The vehicle model formed has been simulated in 3 different driving cycles (WLTP, HFET and US06) and transmission system losses have been compared. In WLTP driving cycle in which speed changes and average speed are low, frictions resulting from the load constitute a significant part of total frictions; on the other hand, in driving cycles in which driving mode is aggressive and the average speed is high, frictions re-sulting from lubricant and sealing elements constitute a significant part of total frictions. Gearbox and related clutch mechanism selection have changed opera-tion interval of the engine during driving cycle.

1 April 2019 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Verified
Journal Article
Closed access
PDF file
MKMEHMET AKİF KUNT
MEHMET AKİF KUNT
HGHaluk Gunes
Haluk Gunes
In this study, a thermoelectric recovery system was designed to convert the exhaust waste heat of an internal combustion diesel engine directly to electric power and the performance was measured at different engine speeds in the unloaded state. The performances of two different thermoelectric generators were compared in a system designed using four modules. Maximum 0.92 W power was obtained for four modules at 3500 r/min, at an area of 0.0016 m2. Internal resistance of modules has increased according to the engine speed. The highest internal resistance obtained during the experiments is 11.69 Ω at engine speed of 3500 r/min. The characteristics of the overall thermoelectric generator performance is coherent with the analysis model. In the current graph according to engine speed, the maximum absolute error is calculated for modules TEG 12-8 and TEG1-199 as 0.010 and 0.044, respectively (at experimented 3500 r/min). To charge the battery under maximum power point conditions, 133 thermoelectric modules were required (TEG1-199). Maximum power transfer is obtained when the load resistor is connected in parallel at 10 Ω. It is seen that modular structure thermoelectric generators are more important alternative than Rankine cycle system in terms of waste heat recovery, despite thermoelectric system has low efficiency.

13 September 2021 in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Verified
Journal Article
Closed access
PDF file
MKMEHMET AKİF KUNT
MEHMET AKİF KUNT
HGHaluk Gunes
Haluk Gunes
Worldwide, motorcycle sales have increased significantly during the coronavirus disease 2019 pandemic process. Thermoelectric generators are technologies that can directly convert waste heat into electrical energy in internal combustion engines. In this study, a waste heat recovery system with a thermoelectric generator has been designed for the exhaust system of a motorcycle engine with a cylinder volume of 50 cc. The performance of the waste heat recovery system has been examined under throttle opening of three-fourth and at different speeds, and a thermal model of the system has been created by means of the GT SUITE model. According to the test results, the increase in engine speed caused different temperature differences on the surfaces of the TEG module due to the constant flow of the fan the maximum recovery power has been found as 2.05 W at an engine speed of 6000 r/min and the maximum system efficiency has been found as 2.41% at an engine speed of 4000 r/min. Following minimum temperature differences have been calculated between experimental and GT SUITE thermal model calculations: 14.05 K at an engine speed of 4000 r/min and at Texh temperatures; 14.1 K at an engine speed of 6000 r/min and at Th temperatures; and 7.5 K at an engine speed of 5500 r/mi and at Tc temperatures.

19 October 2022 in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Verified
Journal Article
Closed access
MKMEHMET AKİF KUNT
MEHMET AKİF KUNT
ACAlper Calam
Alper Calam
HGHaluk Gunes
Haluk Gunes
Engines with homogenous charge compression ignition (HCCI) are the low-temperature combustion models in which automatic oxidation reactions occur with the effect of in-cylinder pressure and heat at the end of preparation of homogenous air-fuel mixture and compression stroke within the cylinder by means of port injection or early direct injection. In-cylinder gas temperatures of such engines during the cycle are lower than conventional internal combustion engines. Therefore, they cause zero NOx and soot emissions. Moreover, the occurrence of combustion in very small crankshaft angles results in a decrease in heat losses observed in cylinder walls and an increase in thermal efficiency. Reducing mechanical friction is highly significant for increasing the effective productivity of HCCI engines. In internal combustion engines, 10% of total energy obtained from the fuel is spent on the heat emerging due to mechanical frictions. 20% of mechanical friction results from the friction occurring between piston ring and liners. In this article, frictional characteristics of compression ring (TOP) and piston skirt area have been examined for two different engine speeds and lubricants, by using technical properties of single-cylinder HCCI engine and in-cylinder pressure and temperature data obtained under full load by means of GT-SUITE software. As the increase in pressure, occurring inside the cylinder at the end of the exhaust stroke and at the beginning of intake stroke, increases ring pressure load in HCCI engines, higher level of piston ring frictions has been observed when compared to internal combustion engines with the same technical properties. Piston ring contact pressure force is a more effective parameter in terms of piston frictions, when compared to hydrodynamic pressure force. The use of lubricants with higher viscosity (SAE 10W-40) has enabled the piston to move more laterally. According to the analysis results, a maximum piston speed of 3.92 m/s for 800 rpm engine speed and 7.85 m/s for 1600 rpm engine speed has been obtained. Maximum friction power losses have been found as 63.84 W at 800 rpm engine speed and 85.91 W at 1600 rpm engine speed. Oil film thickness has obtained in the middle of the piston stroke in the intake, compression, power and exhaust strokes, respectively, 1.809, 1.674, 1.547 and 1.792 µm at 800 rpm engine speed and 1.101, 1.018, 0.932 and 1.119 µm at 1600 rpm engine speed.