Perovskite solar cells (PSCs) have been significantly improved by utilizing an inorganic hole-transporting layer (HTL), such as nickel oxide. Despite the promising properties, there are still limitations due to defects. Recently, research on self-assembled monolayers (SAMs) is being actively conducted, which shows promise in reducing defects and enhancing device performance. In this study, we successfully engineered a p-i-n perovskite solar cell structure utilizing HC-A1 and HC-A4 molecules. These SAM molecules were found to enhance the grain morphology and uniformity of the perovskite film, which are critical factors in determining optical properties and device performance. Notably, HC-A4 demonstrated superior performance due to its distinct hydrophilic properties with a contact angle of 50.3°, attributable to its unique functional groups. Overall, the HC-A4-applied film exhibited efficient carrier extraction properties, attaining a carrier lifetime of 117.33 ns. Furthermore, HC-A4 contributed to superior device performance, achieving the highest device efficiency of 20% and demonstrating outstanding thermal stability over 300 h.
We have investigated the effects of the methylammonium bromide (MABr) content of the precursor solution on the properties of wide-bandgap methylammonium lead tribromide (MAPbBr3) perovskite solar cells (PSCs). In addition, the anti-solvent process for fabricating MAPbBr3 perovskite thin films was optimized. The MAPbBr3 precursor was prepared by dissolving MABr and lead bromide (PbBr2) in N,N-dimethylformamide and N,N-dimethyl sulfoxide. Chlorobenzene (CB) was used as the anti-solvent. We found that both the morphology of the MAPbBr3 layer and the PSCs performance are significantly affected by the MABr content in perovskite precursor solution and anti-solvent dripping time. The best-performing device was obtained when the molar ratio of MABr:PbBr2 was 1:1 and the CB drip time was 10 s. The best device exhibited a power conversion efficiency of 7.58%, short-circuit current density of 7.32 mA·cm−2, open-circuit voltage of 1.30 V, and fill factor of 79.87%.
Organic–inorganic halide perovskite solar cells (PSCs) have excellent chemical, electronic, and optical properties, making them attractive next-generation thin-film solar cells. Typical PSCs were fabricated with a perovskite absorber layer between the TiO2 electron-transport layer (ETL) and the 2,2′,7,7′-tetrakis-(N,N-di-4-methoxyphenylamino)-9,9′-spirobifluorene (Spiro-OMeTAD) hole-transport layer (HTL). We examined the influence of phenyl-C61-butyric acid methyl ester (PCBM) on the PSC device. PSCs using the PCBM layer as an ETL were investigated, and the absorber layer was coated by dissolving PCBM in a methyl ammonium lead iodide (MAPbI3) precursor solution to examine the changes at the perovskite interface and inside the perovskite absorber layer. The PSCs fabricated by adding a small amount of PCBM to the MAPbI3 solution exhibited a significantly higher maximum efficiency of 16.55% than conventional PSCs (14.34%). Fabricating the PCBM ETL and PCBM-MAPbI3 hybrid solid is expected to be an efficient route for improving the photovoltaic performance.
The perovskite solar cells (PSCs) have been significantly improved by utilizing inorganic hole transporting layer (HTL), such as nickel oxide. Despite the promising properties, there are still limitations due to defects. Recently, research on self-assembled monolayers (SAM) is being actively conducted, which show promise in reducing defects and enhancing device performance. In this study, we successfully engineered a p-i-n perovskite solar cell structure utilizing HC-A1 and HC-A4 molecules. These SAM molecules were found to enhance the grain morphology and uniformity of the perovskite film, which are critical factors in determining optical properties and device performance. Notably, HC-A4 demonstrated superior performance due to its distinct hydrophilic properties with a contact angle of 50.3°, attributable to its unique functional groups. Overall, the HC-A4 applied film exhibited efficient carrier extraction properties, attaining a carrier lifetime of 117.33 ns. Furthermore, HC-A4 contributed the superior device performance with its favorable band alignment, achieving the highest device efficiency of 20%.