Anthony Favaloro

Dr. Anthony Favaloro

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in Additive Manufacturing
Verified
Journal Article
Closed access
BBBastian Brenken
Bastian Brenken
EBEduardo Barocio
Eduardo Barocio
AFAnthony Favaloro
Anthony Favaloro
VKVlastimil Kunc
Vlastimil Kunc
RPR. Byron Pipes
R. Byron Pipes

1 March 2019 in Journal of Rheology
Verified
Journal Article
Closed access
PDF file
HTHuan-Chang Tseng
Huan-Chang Tseng
AFAnthony Favaloro
Anthony Favaloro
Over the past three decades, the classic Lipscomb constitutive equation of fiber suspensions in the Newtonian fluids has often been used to discuss the fundamental effects of fiber orientation on flow fields. However, the numerical methods of the Lipscomb flow-fiber coupling employed to simulate anisotropic flows have always been unsatisfactory since convergent results have not been easily obtained, especially in industrial applications for high fiber concentrations. To derive a new informed isotropic (IISO) constitutive equation as an alternative Lipscomb form, particularly introduced with the strain-rate dependent parameter of the Trouton ratio, is a significant requirement. For the fiber-filled polymer melts, the IISO constitutive equation was used herein to predict the rheological behaviors from simple flow to complex flow, including an overshoot of the transient viscosity in shear flow and a dramatic change of the corner vortex in axi-contraction flow. For the practical injection molding simulation c...

10 October 2018 in Journal of Rheology
Verified
Journal Article
Open access
PDF file
AFAnthony Favaloro
Anthony Favaloro
DSDrew E. Sommer
Drew E. Sommer
BDBenjamin R. Denos
Benjamin R. Denos
RPR. Byron Pipes
R. Byron Pipes
Prepreg platelet molding compounds (PPMCs) offer improved performance potential as compared to short-fiber composites and increased geometrical complexity as compared to continuous fiber composites. The increased adoption of PPMCs in automotive and aerospace applications necessitates the development of predictive tools for determining the final orientation state in complex geometries produced through molding flows. Due to the large geometric scale of platelets as compared to molded geometry scales, the orientation structure of PPMCs is spatially nonsmooth, thereby eliminating the requisite separation of scales utilized by typical molding simulation approaches. Additionally, the large fiber volume fraction and fiber length in platelets yield highly anisotropic flow behavior, as manifested in the resistance to stretching deformations along platelet fiber directions. Thus, the goal of this work is to present the development, implementation, and validation of a flow simulation approach for PPMCs accounting for fiber direction and platelet normal direction evolution with coupled anisotropic viscous behavior. The simulation approach is implemented using the smoothed particle hydrodynamics method. To validate the proposed approach, a pin bracket geometry is manufactured from a charge with the orientation state measured by computed tomography (CT). The final orientation state determined by the flow simulation predictions and by measuring the orientation state of the final bracket by CT is compared to validate the predictions.

Verified
Journal Article
Open access
PDF file
NSNathan D. Sharp
Nathan D. Sharp
JGJohnathan E. Goodsell
Johnathan E. Goodsell
AFAnthony Favaloro
Anthony Favaloro
The orientation of fibers with elliptical cross-sections cannot be estimated using standard optical microscopy analysis methods in which the ratio of the minor-axis to the major-axis and orientation of the major-axis are directly used to determine the fiber spherical coordinates, θ and ϕ . A new method for estimating the orientation of fibers with elliptical cross-sections is presented and validated using both simulations and experiments. Fibers with elliptical cross-sections rather than circular possess a roll degree of freedom, which significantly affects the dimensions of projected cross-sections in viewing planes. The equations of the projected ellipse of an elliptic cylinder onto a viewing plane are determined in terms of typical spherical coordinate system angles, θ and ϕ , the roll angle, α , and the fiber semi-major and semi-minor diameters. Fiber angles are determined by numerical fitting of the developed equations to measured ellipses. An ambiguity in the determined angles is identified, and, in the special case of fiber bundles, a scheme is presented by which the ambiguity can be resolved. Validation experiments showed that the method is quite effective at estimating fiber orientation from micrographs when fiber cross-section dimensions are measured beforehand, and the additional ambiguity is resolved easily in the case of fiber bundles.

19 February 2024 in Composites Part B: Engineering
Verified
Journal Article
Closed access
EBEduardo Barocio
Eduardo Barocio
JHJustin Hicks
Justin Hicks
GKGaram Kim
Garam Kim
AFAnthony Favaloro
Anthony Favaloro
GGGourab Ghosh
Gourab Ghosh
RPR. Byron Pipes
R. Byron Pipes

1 May 2020 in Journal of Rheology
Verified
Journal Article
Closed access
PDF file
AFAnthony Favaloro
Anthony Favaloro
DSDrew E. Sommer
Drew E. Sommer
Prepreg platelet molding compounds (PPMCs) have mesoscale (platelet scale) features that are not found in injection molding materials. Beyond the fiber orientation state, the platelet normal orientation state and the expected orientation state variabilities are desirable outputs from flow simulations of PPMC systems. However, theoretical understanding and efficient numerical molding simulation capabilities have primarily been developed for injection molding. Using exact solutions of Jeffery’s equation, two methods are developed: approximation of the second-order normal orientation tensor as a function of the second-order fiber orientation tensor and estimation of the variability in predicted orientation tensors due to scale similarity of the platelets and typical molded geometry thicknesses. These methods are validated using orientation state data obtained from computed tomography for five replicates of a PPMC bracket structure. Finally, the methods are applied as postprocessing of a fiber orientation simulation results, showing good comparison with the experimental data. The developed methods allow existing simulation capabilities to be applied to PPMCs as a reduced order model to enable efficient design iterations for PPMC manufacturing.Prepreg platelet molding compounds (PPMCs) have mesoscale (platelet scale) features that are not found in injection molding materials. Beyond the fiber orientation state, the platelet normal orientation state and the expected orientation state variabilities are desirable outputs from flow simulations of PPMC systems. However, theoretical understanding and efficient numerical molding simulation capabilities have primarily been developed for injection molding. Using exact solutions of Jeffery’s equation, two methods are developed: approximation of the second-order normal orientation tensor as a function of the second-order fiber orientation tensor and estimation of the variability in predicted orientation tensors due to scale similarity of the platelets and typical molded geometry thicknesses. These methods are validated using orientation state data obtained from computed tomography for five replicates of a PPMC bracket structure. Finally, the methods are applied as postprocessing of a fiber orientation sim...