Radiant floor heating has received increasing attention due to its diverse advantages, especially the energy saving as compared to the conventional dwelling heating system. This paper presents a numerical investigation of airflow and heat transfer in the slot‐vented room with the radiant floor heating unit. Combination of fluid convection and thermal radiation has been implemented through the thermal boundary conditions. Spatial distributions of indoor air temperature and velocity, as well as the heat transfer rates along the radiant floor and the outer wall, have been presented and analyzed covering the domains from complete natural convection to forced convection dominated flows. The numerical results demonstrate that the levels of average temperature in the room with lateral slot‐ventilation are higher than those without slot‐ventilation, but lower than those in the room with ceiling slot‐ventilation. Overall, the slot‐ventilation room with radiant floor heating unit could offer better indoor air quality through increasing the indoor air temperature and fresh air exchanging rate simultaneously. Concerning the airborne pollutant transports and moisture condensations, the performance of radiant floor heating unit will be further optimized in our future researches.
8 April 2020 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Diesel engines are common power generation equipments used in offshore oil production facilities, and their waste heat can be recycled. But the working conditions of diesel engines usually vary with the fluctuated electricity loads due to the unstable crude oil production. In this paper, the off-design conditions were identified under the variable loads. Then, with the ideal air standard Brayton cycle for diesel engines, thermodynamic models of the system with/without heat recovery were developed to study the effects of the pressure ratio and temperature ratio on the thermal efficiency and exergy efficiency of diesel engines. The results show that for the irreversible Brayton system without heat recovery, the thermal efficiency and exergy efficiency increase with the increase of pressure ratio until reaching the peak value, then decrease with the increase of the pressure ratio under the constant temperature ratio. Under the condition of β = 0.25, 0.50, 0.75, 1.0, and 1.10, the highest value of ε efficiency is 0.2517, 0.3302, 0.3913, 0.4168, and 0.4391, respectively (when there is no residual heat recovery); And the highest value of ε efficiency is 0.4645, 0.5448, 0.6053, 0.6297, and 0.6507, respectively (when there is residual heat recovery). Our research can optimize the performance of the compressor pressure ratio and temperature ratio parameters of the thermal power plant under the condition of variable load of diesel engine, which has a high reference value for the transformation of waste heat recovery.
Air-source heat-pump (ASHP) water heater provides an important low-carbon solution for domestic water heating, which regains interest in the context of pursuing global carbon neutrality. In this study, a novel testing and theoretical approach is proposed for ASHP water heater with flash tank vapor-injection by retrofitting the testing methods of state points. Five flash tank vapor-injections with different temperature levels are tested and verified the testing method for ASHP water heater. On basis of the tested compressor suction temperature, exhaust temperature, electronic expansion valve pre-throttle temperature, electronic expansion valve throttling temperature and vapor-injection temperature, a thermodynamic analysis is conducted to determine the system performances. The relationship between the vapor-injection pressure ratio, system heating capacity and COP is identified by adjusting the expansion valve opening degree of the system. The results show that the COP of the system firstly decreases and subsequently increases with the increase in vapor-injection pressure ratio, and the minimum COP appears when the vapor-injection pressure ratio is 0.3. This study provides new insights into the advanced ASHP water heater.
This study aims to accurately characterize the nonlinear stress–strain evolution of rocks under uniaxial compression considering crack propagation. First, the rock meso-structure was generalized into intact rock unit cells, crack propagation damage unit cells, and pore unit cells according to phenomenological theory. A mesoscopic rock stress model considering crack propagation was established based on the static equilibrium relationship of the unit cells, and the effective stress of the crack propagation damage unit cells was solved based on fracture mechanics. Then, the geometric damage theory and conservation-of-energy principle were introduced to construct the damage evolution equation for rock crack propagation. On this basis, the effective stress of the damage unit cells and the crack propagation damage equation were incorporated into the rock meso-structure static equilibrium equation, and the effect of nonlinear deformation in the soft rock compaction stage was considered to establish a rock damage constitutive model based on mesoscopic crack propagation evolution. Finally, methods for determining model parameters were proposed, and the effects of the model parameters on rock stress–strain curves were explored. The results showed that the theoretical model calculations agreed well with the experimental results, thus verifying the rationality of the damage constitutive model and the clear physical meaning of the model parameters.