Climate sensitive urban planning involves the implementation of green infrastructure as one measure to mitigate excessive heat in urban areas. Depending on thermal conditions, certain trees tend to emit more biogenic volatile organic compounds, which act as precursors for ozone formation, thus hampering air quality. Combining a theoretical approach from a box model analysis and microscale modeling from the microclimate model ENVI-met, we analyze this relationship for a selected region in Germany and provide the link to air quality prediction and climate sensitive urban planning. A box model study was conducted, indicating higher ozone levels with higher isoprene concentration, especially in NO-saturated atmospheres. ENVI-met sensitivity studies showed that different urban layouts strongly determine local isoprene emissions of vegetation, with leaf temperature, rather than photosynthetic active radiation, being the dominant factor. The impact of isoprene emission on the ozone in complex urban environments was simulated for an urban area for a hot summer day with and without isoprene. A large isoprene-induced relative ozone increase was found over the whole model area. On selected hot spots we find a clear relationship between urban layout, proximity to NOx emitters, tree-species-dependent isoprene emission capacity, and increases in ozone concentration, rising up to 500% locally.
While complex urban morphologies including different materials, wall structures, etc., are rather adequately represented in microclimate models, replication of actual plant geometry is—so far—rather crudely handled. However, plant geometry greatly differs within species and locations while strongly determining a plant’s microclimate performance. To improve the plants representation in numerical models, a new method to describe plant skeletons using the so-called Lindenmayer-System has been implemented in the microclimate model ENVI-met. The new model allows describing much more realistic plants including the position and alignment of leaf clusters, a hierarchical description of the branching system and the calculation of the plant’s biomechanics. Additionally, a new canopy radiation transfer module is introduced that allows not only the simulation of diffuse radiation extinction but also secondary sources of diffuse radiation due to scattering of direct radiation within plant canopies. Intercomparisons between model runs with and without the advancements showed large differences for various plant parameters due to the introduction of the Lindenmayer-System and the advanced radiation scheme. The combination of the two developments represents a sophisticated approach to accurately digitize plants, model radiative transfer in crown canopies, and thus achieve more realistic microclimate results.
Accurate simulation of radiative transfer is a very important aspect in climate modeling. For microclimate models in particular, it is not only important to simulate primary but also secondary radiative fluxes in great detail, i.e., emitted longwave and reflected shortwave radiation. As there are always limitations regarding computational effort and memory, these radiative fluxes are commonly implemented using simplified approaches. To overcome these simplifications and, thus, increase modeling accuracy, a new radiation scheme called indexed view sphere was introduced into the microclimate model ENVI-met. This new scheme actually accounts for radiative contributions of objects that are seen by each grid cell. In order to evaluate the advantages of the new scheme, it is compared against the formerly used averaged view factor scheme. The comparison in a complex realistic urban environment demonstrated that the indexed view sphere scheme improved the accuracy and plausibility of modeling radiative fluxes. It, however, yields an increased demand of memory to store the view facets for each cell. The higher accuracy in simulating secondary radiative fluxes should, however, overturn this shortcoming for most studies, as more detailed knowledge of local microclimatic conditions in general and eventually thermal comfort can be gained.
The number of studies evaluating flux or concentration footprints has grown considerably in recent years. These footprints are vital to understand surface–atmosphere flux measurements, for example by eddy covariance. The newly developed backwards trajectory model LaStTraM (Lagrangian Stochastic Trajectory Model) is a post-processing tool, which uses simulation results of the holistic 3D microclimate model ENVI-met as input. The probability distribution of the particles is calculated using the Lagrangian Stochastic method. Combining LaStTraM with ENVI-met should allow us to simulate flux and concentration footprints in complex urban environments. Applications and evaluations were conducted through a comparison with the commonly used 2D models Kormann Meixner and Flux Footprint Predictions in two different meteorological cases (stable, unstable) and in three different detector heights. LaStTraM is capable of reproducing the results of the commonly used 2D models with high accuracy. In addition to the comparison with common footprint models, studies with a simple heterogeneous and a realistic, more complex model domain are presented. All examples show plausible results, thus demonstrating LaStTraM’s potential for the reliable calculation of footprints in homogeneous and heterogenous areas.
In the summer of 2022, an intense heatwave swept through Northern Europe, with London bearing a significant impact. While nature-based solutions are often considered to be ideal responses to such heatwaves, experiences from the 2022 heatwave and others revealed potential drawbacks, particularly for urban green spaces. Prolonged dry spells, frequently accompanying heatwaves, result in excessively dry soil and the subsequent decline of vegetation in large parks. In the present study, microclimate simulations were conducted for Hyde Park in London, a location that experienced such drought during the 2022 heatwave, to examine its microclimatic performance in terms of thermal comfort and tree health. In alignment with the observations, ENVI-met could replicate the lack of noticeable cooling effects during the daytime and only marginal cooling during the nighttime. To address these challenges, mitigation scenarios were explored, incorporating heat mitigation measures such as part-time irrigation, temporary sun sails, and façade greenery. The findings demonstrated that implementing these measures could reduce heat stress by up to 13 K PET (physiologically equivalent temperature). These practical solutions emerged as effective remedies for mitigating the impact of heatwaves on urban green spaces and, hence, improving future urban development overall.