Donghai Jin

Prof. Donghai Jin


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 April 2018 in Journal of Fluids Engineering
Verified
Journal Article
Closed access
PDF file
XDXu Dong
Xu Dong
DSDakun Sun
Dakun Sun
FLFanyu Li
Fanyu Li
DJDonghai Jin
Donghai Jin
XGXingmin Gui
Xingmin Gui
XSXiaofeng Sun
Xiaofeng Sun
Swirl inlet distortion is usually encountered in modern flight vehicles since their inlet ducts usually consist of one or two bends, such as S-inlet duct. An experimental device is first designed to simulate the swirl inlet distortion and then used to test the effectiveness of a novel casing treatment (CT) on a low-speed compressor under the swirl distortions of various intensities. The influences of co- and counter-rotating swirl inlet distortion on the test compressor and the stabilization ability of this novel CT are well demonstrated by the illustrations of static pressure rise curves and efficiency curves. The dynamic prestall pressure signals are also captured to reflect the perturbation energy in the flow field through which the mechanism of the novel CT will be indicated. The relevant results show that counter-rotating swirl distortion in small intensity could increase the compressive ability of compressor with small efficiency loss, and the co-rotating swirl distortion always brings about detrimental effects on compressor performance. At the same time, the distortion of twin swirls can cause nonuniform total pressure profile which can seriously damage the compressor performance. Besides, the stall precursor-suppressed (SPS) CT shows a good capability of stall margin (SM) enhancement no matter what swirl inlet distortions are encountered in the test compressor.

1 November 2015 in Journal of Fluids Engineering
Verified
Journal Article
Closed access
PDF file
XDXu Dong
Xu Dong
DSDakun Sun
Dakun Sun
FLFanyu Li
Fanyu Li
DJDonghai Jin
Donghai Jin
XGXingmin Gui
Xingmin Gui
XSXiaofeng Sun
Xiaofeng Sun
This paper conducts an experimental research of rotating inlet distortion on a low-speed large size test compressor with emphasis on the stability problem of axial fan/compressors, and the stall margin enhancement with a kind of stall precursor-suppressed (SPS) casing treatment. Some results on compressor stall margin and prestall behavior under the restriction of rotating inlet distortion are presented. The experimental results show that whether the inlet distortion is co-rotating or counter-rotating, the SPS casing treatment can still improve the stall margin without leading to additional efficiency loss caused by such configuration. The experiment results also show that the mechanism of the stall margin improvement with such casing treatment is associated with delaying the nonlinear development of the stall precursor waves and weakening the unsteady flow disturbances in a compression system.

1 January 2019 in ASAIO Journal
Verified
Journal Article
Closed access
GLGuang-Mao Liu
Guang-Mao Liu
DJDonghai Jin
Donghai Jin
JZJian-Ye Zhou
Jian-Ye Zhou
YZYan Zhang
Yan Zhang
HCHai-Bo Chen
Hai-Bo Chen
XGXing-Min Gui
Xing-Min Gui
The gaps between the blades and the shroud (or hub) of an axial blood pump affect the hydraulics, efficiency, and hemolytic performance. These gaps are critical parameters when a blood pump is manufactured. To evaluate the influence of blade gaps on axial blood pump performance, the flow characteristics inside an axial blood pump with different radial blade gaps were numerically simulated and analyzed with special attention paid to the hydraulic characteristics, gap flow, hydraulic efficiency, and hemolysis index (HI).In vitrohydraulic testing and particle image velocimetry testing were conducted to verify the numerical results. The simulation results showed that the efficiency and pressure rise decreased when the gap increased. The efficiency of the axial blood pump at design point decreased from 37.1% to 27.1% and the pressure rise decreased from 127.4 to 71.2 mm Hg when the gap increased from 0.1 to 0.3 mm. Return and vortex flows were present in the outlet guide vane channels when the gap was larger than 0.2 mm. The HI of the blood pump with a 0.1 mm gap was 1.5-fold greater than that with a 0.3 mm gap. The results illustrated poor hydraulic characteristics when the gap was larger than 0.15 mm and rapidly deteriorated hemolysis when the gap was larger than 0.1 mm. The numerical and experimental results demonstrated that the pressure rise, pump efficiency, and scalar shear stress decreased when the gap increased. The HI did not strictly decrease with gap increases. The preliminary results encourage the improvement of axial blood pump designs.

15 January 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DLDong LIANG
Dong LIANG
XGXingmin Gui
Xingmin Gui
DJDonghai Jin
Donghai Jin
In order to investigate the effect of seal cavity leakage flow on a compressor’s performance and the interaction mechanism between the leakage flow and the main flow, a one-stage compressor with a cavity under the shrouded stator was numerically simulated using an inhouse circumferentially averaged through flow program. The leakage flow from the shrouded stator cavity was calculated simultaneously with main flow in an integrated manner. The results indicate that the seal cavity leakage flow has a significant impact on the overall performance of the compressor. For a leakage of 0.2% of incoming flow, the decrease in the total pressure ratio was 2% and the reduction of efficiency was 1.9 points. Spanwise distribution of the flow field variables of the shrouded stator shows that the leakage flow leads to an increased flow blockage near the hub, resulting in drop of stator performance, as well as a certain destructive effect on the flow field of the main passage.

19 December 2023 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
SWShuhao Wang
Shuhao Wang
DJDonghai Jin
Donghai Jin
YZYin Zhang
Yin Zhang
KWKun Wang
Kun Wang
XGXingmin Gui
Xingmin Gui

4 January 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
XLXiaoheng Liu
Xiaoheng Liu
KWKe Wan
Ke Wan
DJDonghai Jin
Donghai Jin
XGXingmin Gui
Xingmin Gui
Gas turbine engines are highly intricate machines, and every component of them is closely associated with one another. In the traditional engine developing process, vast experiment tests are needed. To reduce unnecessary trials, a whole gas turbine engine simulation is extremely needed. For this purpose, a compressor simulation tool is now developed. Considering the inherent drawbacks of 0D analysis and 3D CFD (Computational Fluid Dynamics) calculation, the 2D throughflow method is an indispensable tool. Based on the circumferential average method (CAM), 3D Navier–Stokes is transformed into a 2D method. One phenomenon arising is that the lack of description about circumferential motion leads to the need for the blade force modeling in compressor simulation. Previous models are based on the assumption that flow passes through the average stream surface without entropy increasing, which is not applicable in the CAM. An improved model is proposed based on the result analysis from CAM and NUMECA method in a linear cascade. Whereafter, the model is applied in a highly loaded and low-speed fan, which has been tested for its performance characteristics. Utilizing the new model, the error of the adiabatic efficiency between CAM and experiment decreases from 4.0% to 1.0% and the accuracy of the mass flow, and pressure ratio remains unchanged. The time involved in the CAM simulation is nearly 70 times faster than that of the 3D simulation.