The main aim of this study was to explore the safety differences when using aluminum alloy and three different fiber reinforced composites as material for the cockpit and fuselage of light aircraft under crash landing. In accordance with the cockpit reduction amount stipulated by MIL-STD-1290A in which the reducing rates in all directions cannot exceed 15%, this study established the safety zones of impact speeds and impact angles. The overall safety zones of the carbon fiber reinforced composites and glass fiber reinforced composites cockpits were higher than that of the aluminum alloy cockpit by 38.56% and 32.12%, respectively. Among the four different fuselage materials, when carbon fiber reinforced composites was used as the cockpit material, except that the reducing rate for the crashing in the Y direction was slightly higher than the aluminum alloy cockpit, the reducing rate in the X direction and the inclined beam A direction during crashes were less than other materials, and the safety of its overall cockpit was also the most superior to other materials. The energy absorption capability of the aluminum alloy fuselage was better than the fuselages of all composite materials.
23 November 2015 in Materials Research Innovations
This study uses finite element analysis software to conduct simulations and compares the fatigue behaviour of the aluminium alloy and glass fibre-reinforced composite that is used in light aircraft landing gear. The maximum stress, maximum strain and deformation of landing gear of different shapes (plate and tube shapes) are also determined. The results show that the composite landing gear weighs 45% less than an aluminium equivalent. Of the samples tested, plate-shaped glass fibre-reinforced composite landing gear exhibits the lowest maximum stress under a static load. Regardless of whether the landing gear is plate- or tube-shaped, the maximum strain and deformation for the composite landing gear are more than four times those for the aluminium alloy landing gear. The results for dynamic load show that plate-shaped glass fibre-reinforced composite and tube-shaped aluminium landing gear have similar maximum alternating stress under cyclic loading.
1 December 2013 in Transactions of the Canadian Society for Mechanical Engineering
This study uses the finite element software, FRANC2D, and the life-time analysis software, AFGROW, to perform simulation analyses of the damage tolerance of the landing gear of light aviation vehicles. This study explores the effect that the initial crack positions and different materials have on the life cycle of landing gear under long-term loads. This study also compares the relationship between stress intensity factors and crack growth for four types of aluminum alloys, titanium alloy and alloy steel. The relationship between residual strength and life cycle, in the presence of existing cracks, is also investigated.
1 December 2015 in Transactions of the Canadian Society for Mechanical Engineering
This study analyzes the crashworthiness of a light aircraft that is constructed from composite materials. The finite element method is employed to conduct dynamic impact simulations on carbon fiber composite fuselages. The results show that the safe impact speed for an aluminum alloy cockpit crashed at a 30° impact angle is 9.59 m/s, but a cockpit made of composite material can withstand a speed greater than 18.05 m/s. The safe impact angle for an aluminum alloy cockpit is 16.56°, but that for a composite cockpit is 84.9°. The safety crash zone for a composite material cockpit is 160% greater than that for an aluminum alloy cockpit.
Due to the demands of personal travels and entertainments, light airplanes and small business aircrafts are developing rapidly. Light airplane structure is simple; however, it lacks crashworthiness design, especially the considerations on the impact of energy absorption. Therefore, in an event of accident, significant damage to passengers will be usually incurred. Airplanes made of composite materials structurally have high specific strength and good aerodynamic configuration. These materials have become the primary choice for new airplane development. This study mainly explores the topology optimization analysis of the light aircraft’s cockpit made of carbon fiber reinforced composites. This paper compares the compression amounts in the original models of composite material and aluminum alloy fuselages with the models after optimization during the crash-landing, in order to investigate the safety of fuselages made of different materials after structural optimization under the dynamic crashing. This study found that the energy absorbed by the aluminum alloy fuselage during crash-landing is still higher than that by the carbon fiber reinforced composites fuselage. On the other hand, the aluminum alloy fuselage after topology optimization could have an energy absorption capability enhanced by 40%, as compared to the that of the original model of aluminum alloy fuselage.