Javier Bonilla

Prof. Javier Bonilla

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 November 2019 in Frontiers in Energy Research
Verified
Journal Article
Open access
PDF file
JBJavier Bonilla
Javier Bonilla
GGGerardo Gordillo
Gerardo Gordillo
CCCarlos Cantor
Carlos Cantor
This work discusses results on temperature profile, syngas composition, High Heating Value, and efficiency of a Coffee Husk counter-current fixed-bed gasification process, in which oxygen-steam blends were used as an oxidizing agent. The experimentation was carried out for various Equivalence Ratios (ER) and Steam-Fuel Ratios (SF), whose ranges were [1.6–5.6] and [0.4–0.8], respectively. The results show that increased steam (higher steam fuel ratios) improves the H2/CO molar ratio i.e., for a constant ER = 3.7 and SF at 0.4, 0.6, and 0.8, the H2/CO ratio was 1.2, 1.4, and 1.8, respectively. Also, the addition of steam tends to increase the syngas Higher Heating Value, which ranged between 7,714 kJ/m3 at ER = 1.6 and SF = 0.4 and 8,841 kJ/m3 at ER = 3.2 and SF = 0.8. On the other hand, increased ER (lower oxygen) decreases the Net Cold Gasification Efficiency (CGENET) which was between 53% at ER = 5.6 and SF = 0.6 and 82% at ER = 1.6 and SF = 0.4. Results were also compared to results published before for gasification of the same biomass but using air-steam mixtures for partial oxidation. This comparison shows that the use of oxygen increases both the temperature profile in the bed and the yield of CO and H2 contained in the syngas.

1 October 2019 in Heliyon
Verified
Journal Article
Open access
JBJavier Bonilla
Javier Bonilla
RSRobert Paul Salazar
Robert Paul Salazar
MBManuel Alejandro Mayorga Betancourt
Manuel Alejandro Mayorga Betancourt
The potential of sawmill wastes as a raw material in pyrolysis process is presented in this study. Non-isothermal thermogravimetric analysis (TGA and DTG) and isoconversional methods were employed to determine triplet kinetic (activation energy, reaction model and pre-exponential factor). Through TGA and DTG, the conversion degree is described as a function of temperature for five heating rates (10, 20, 30, 40 and 50 o C/min) and four model-free methods (Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS), Friedman, and Vyazovkin) with temperatures ranging from 25 to 1000 ° C were employed. Isoconversional lines were built for every method at different isoconversional degrees α ∈ [ 0,1 ] . The activation energy E was found as a function of α in the interval χ I I = [ 0.2 , 0.7 ] where each isoconversional methods were in agreement and the estimated error was sufficiently small. Findings show the same activation energy profile independently of the isoconversional method. In particular the total variation of E in χ I I was as follows: 209.909-228.238 kJ/mol (FWO); 211.235-229.277 kJ/mol (KAS); 223.050-188.512 kJ/mol (Friedman), and 211.449 kJ/mol-229.512 kJ/mol (Vyazovkin). The reaction model of the process in χ I I matched with a two-dimensional diffusion ( D 2 ) by using a master-plot analysis. The calculated and reported parameters are fundamental information for the pyrolysis reactor design using Sawmill wastes as feedstock.

8 November 2019 in Energies
Verified
Journal Article
Open access
PDF file
CRCamilo Andrés Bayona Roa
Camilo Andrés Bayona Roa
JCJuan Sebastián Solís Chaves
Juan Sebastián Solís Chaves
JBJavier Bonilla
Javier Bonilla
ARA.G. Rodriguez-Melendez
A.G. Rodriguez-Melendez
DPdiego castellanos proaños
diego castellanos proaños
Instead of simplified steady-state models, with modern computers, one can solve the complete aero-thermodynamics happening in gas turbine engines. In the present article, we describe a mathematical model and numerical procedure to represent the transient response of a PT6A gas turbine engine operating at off-design conditions. The aero-thermal model consists of a set of algebraic and ordinary differential equations that arise from the application of the mass, linear momentum, angular momentum and energy balances in each engine’s component. The solution code has been developed in Matlab-Simulink® using a block-oriented approach. Transient simulations of the PT6A engine start-up have been carried out by changing the original Jet-A1 fuel with biodiesel blends. Time plots of the main thermodynamic variables are shown, especially those regarding the structural integrity of the burner. Numerical results have been validated against reported experimental measurements and GasTurb® simulations. The computer model has been capable to predict acceptable fuel blends, such that the real PT6A engine can be substituted to avoid the risk of damaging it.

13 September 2017 in Journal of Combustion
Verified
Journal Article
Open access
PDF file
JBJavier Bonilla
Javier Bonilla
GGGerardo Gordillo
Gerardo Gordillo
The increasing energy consumption, mostly supplied by fossil fuels, has motivated the research and development of alternative fuel technologies to decrease the humanity’s dependence on fossil fuels, which leads to pollution of natural sources. Small-scale biomass gasification, using air-steam blends for partial oxidation, is a good alternative since biomass is a neutral carbon feedstock for sustainable energy generation. This research presents results obtained from an experimental study on coffee husk (CH) gasification, using air-steam blends for partial oxidation in a 10 kW fixed-bed gasifier. Parametric studies on equivalence ratio (ER) (1.53 < ER < 6.11) and steam-fuel (SF) ratio (0.23 < SF < 0.89) were carried out. The results show that increasing both SF and ER results in a syngas rich in CH4 and H2 but poor in CO. Also, decreased SF and ER decrease the peak temperature (Tpeak) at the gasifier combustion zone. The syngas high heating value (HHV) ranged from 3112 kJ/SATPm3 to 5085 kJ/SATPm3 and its maximum value was obtained at SF = 0.87 and ER = 4.09. The dry basis molar concentrations of the species, produced under those operating conditions (1.53 < ER < 6.11 and 0.23 < SF < 0.89), were between 1.12 and 4.1% for CH4, between 7.77 and 13.49% for CO, and between 7.54 and 19.07% for H2. Other species were in trace amount.

19 June 2019 in Preprints.org
Verified
Preprint
Open access
JCJuan Sebastián Solís Chaves
Juan Sebastián Solís Chaves
CBCamilo Bayona
Camilo Bayona
JBJavier Bonilla
Javier Bonilla
DCDiego Castellanos
Diego Castellanos
A computational simulation of a PT6A gas turbine engine operating at off-design conditions is described in the present article. The model consists of a 0-dimensional thermo-fluidic description of the engine by applying the mass, linear momentum, angular momentum, and energy balances in each engine's component. The transient behavior of the engine is simulated for different blends of the original JET-A1 fuel with bio-diesel. Simulated thermodynamic variables of the air at each engine's component, as well as some performance parameters correspond to the reported experimental measurements. The numerical results also demonstrate the ability of the computational simulation to predict acceptable fuel blends, such that the efficiency of the engine is maximized and its structural integrity is maintained.