Ming Gao

Ming Gao


Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 July 2013 in Optics Express
Verified
Journal Article
Closed access
PDF file
LGL.B. Guo
L.B. Guo
ZHZ.Q. Hao
Z.Q. Hao
MSM. Shen
M. Shen
WXW. Xiong
W. Xiong
XHX.N. He
X.N. He
YLY.F. Lu
Y.F. Lu
To improve the accuracy of quantitative analysis in laser-induced breakdown spectroscopy, the plasma produced by a Nd:YAG laser from steel targets was confined by a cavity. A number of elements with low concentrations, such as vanadium (V), chromium (Cr), and manganese (Mn), in the steel samples were investigated. After the optimization of the cavity dimension and laser fluence, significant enhancement factors of 4.2, 3.1, and 2.87 in the emission intensity of V, Cr, and Mn lines, respectively, were achieved at a laser fluence of 42.9 J/cm2 using a hemispherical cavity (diameter: 5 mm). More importantly, the correlation coefficient of the V I 440.85/Fe I 438.35 nm was increased from 0.946 (without the cavity) to 0.981 (with the cavity); and similar results for Cr I 425.43/Fe I 425.08 nm and Mn I 476.64/Fe I 492.05 nm were also obtained. Therefore, it was demonstrated that the accuracy of quantitative analysis with low concentration elements in steel samples was improved, because the plasma became uniform with spatial confinement. The results of this study provide a new pathway for improving the accuracy of quantitative analysis of LIBS.

28 February 2014 in Materials
Verified
Journal Article
Open access
PDF file
MGMing Gao
Ming Gao
CCCong Chen
Cong Chen
YGYunze Gu
Yunze Gu
XZXiaoyan Zeng
Xiaoyan Zeng
Fiber laser-cold metal transfer arc hybrid welding was developed to welding-braze dissimilar Al and Ti alloys in butt configuration. Microstructure, interface properties, tensile behavior, and their relationships were investigated in detail. The results show the cross-weld tensile strength of the joints is up to 213 MPa, 95.5% of same Al weld. The optimal range of heat input for accepted joints was obtained as 83–98 J·mm−1. Within this range, the joint is stronger than 200 MPa and fractures in weld metal, or else, it becomes weaker and fractures at the intermetallic compounds (IMCs) layer. The IMCs layer of an accepted joint is usually thin and continuous, which is about 1μm-thick and only consists of TiAl2 due to fast solidification rate. However, the IMCs layer at the top corner of fusion zone/Ti substrate is easily thickened with increasing heat input. This thickened IMCs layer consists of a wide TiAl3 layer close to FZ and a thin TiAl2 layer close to Ti substrate. Furthermore, both bead shape formation and interface growth were discussed by laser-arc interaction and melt flow. Tensile behavior was summarized by interface properties.

24 March 2019 in Science and Technology of Welding and Joining
Verified
Journal Article
Closed access
SZShuai Zhang
Shuai Zhang
YZYazhou Zhang
Yazhou Zhang
MGMing Gao
Ming Gao
FWFude Wang
Fude Wang
QLQuan Li
Quan Li
XZXiaoyan Zeng
Xiaoyan Zeng
A hybrid technique integrating wire arc additive manufacturing (WAAM) and milling was studied using Al5Si aluminium alloy. The results showed both the surface roughness and the machining allowance of this hybrid additive/subtractive manufacturing were reduced in comparison with pure WAAM when the milling thickness was in the range of 0.4–1.2 mm. The accuracy improvement was discussed in terms of the melt flow. It was found that after the surface was milled to a plane, the melt flow changed from the downward along camber surface to the outward and backflow on the plane. This change slowed down the velocity of melt flow, and then reduces the fluctuation of the side profile of deposited thin wall.

29 November 2018 in Science and Technology of Welding and Joining
Verified
Journal Article
Closed access
LWLei Wang
Lei Wang
MGMing Gao
Ming Gao
XZXiaoyan Zeng
Xiaoyan Zeng
Effects of oscillating diameter (D) and frequency (f) on weld surface and cross-sectional morphologies were investigated in laser welding of AA6061 aluminium alloy with circular beam oscillation. Weld surface was mainly characterised by straight line shape when f > 10 Hz. Weld cross-section transformed from slender nail to irregular shape, dumpy nail, rectangle and crescent shape in sequence with the increase of D and f. A modified model considering material thermal properties was developed to predict the surface feature, especially whether the weld totally overlapped or not. A new normalised enthalpy was proposed to predict the keyhole mode of laser oscillating welding by considering materials thermal properties and remelting effect, which was suitable to explain the formation of cross-sectional morphology.

29 May 2014 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
MGMing Gao
Ming Gao
CCCong Chen
Cong Chen
SMShuwen Mei
Shuwen Mei
LWLei Wang
Lei Wang
XZXiaoyan Zeng
Xiaoyan Zeng

1 April 2019 in Optics & Laser Technology
Verified
Journal Article
Closed access
YMYunfei Meng
Yunfei Meng
XLXinwei Li
Xinwei Li
MGMing Gao
Ming Gao
XZXiaoyan Zeng
Xiaoyan Zeng