Emanuela Natale

Dr. Emanuela Natale

University of L'Aquila, Department of Industrial and Information Engineering and Economics
orcid

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2007 in Robotics and Computer-Integrated Manufacturing
Verified
Journal Article
Closed access
Giulio D'EmiliaGiulio D'Emilia
Giulio D'Emilia
AMAntonio Marra
Antonio Marra
Emanuela NataleEmanuela Natale
Emanuela Natale

6 April 2018 in Journal of Sensors and Sensor Systems
Verified
Journal Article
Open access
PDF file
Giulio D'EmiliaGiulio D'Emilia
Giulio D'Emilia
Antonella GaspariAntonella Gaspari
Antonella Gaspari
FMFabrizio Mazzoleni
Fabrizio Mazzoleni
Emanuela NataleEmanuela Natale
Emanuela Natale
ASAlessandro Schiavi
Alessandro Schiavi
Two alternative experimental procedures for the calibration of tri-axial accelerometers have been compared with traditional methods, performed according the procedures stated in the standard ISO 16063-21. Standard calibration is carried out by comparison with a laser Doppler vibrometer (LDV), used as a primary reference transducer. The main sensitivities have been investigated and, where applicable, also transverse ones. Many aspects have been evaluated: the hypotheses about transverse sensitivities, the simplicity of the procedure, the number of measurements needed, and the effect of typology of transducer, depending on electrical and geometrical contributions. Two different accelerometers have been tested, a piezo-electric accelerometer and a capacitive MEMS accelerometer. A low-frequency range of vibration has been investigated, 3 and 6 Hz, with amplitude of acceleration ranging from 2 to 20 ms−2. A satisfactory reproducibility of methods has been verified, with percentage differences less than 2.5 %. Anyway, pros and cons of each method are also discussed with reference to their possible use for easy and quick calibration of low-cost tri-axial accelerometers.

23 May 2018 in Journal of Sensors and Sensor Systems
Verified
Journal Article
Open access
PDF file
Giulio D'EmiliaGiulio D'Emilia
Giulio D'Emilia
Antonella GaspariAntonella Gaspari
Antonella Gaspari
FMFabrizio Mazzoleni
Fabrizio Mazzoleni
Emanuela NataleEmanuela Natale
Emanuela Natale
ASAlessandro Schiavi
Alessandro Schiavi
A comparison among three methods for the calibration of tri-axial accelerometers, in particular MEMS, is presented in this paper, paying attention to the uncertainty assessment of each method. The first method is performed according to the ISO 16063 standards. Two innovative methods are analysed, both suitable for in-field application. The effects on the whole uncertainty of the following aspects have been evaluated: the test bench performances in realizing the reference motion, the vibration reference sensor, the geometrical parameters and the data processing techniques. The uncertainty contributions due to the offset and the transverse sensitivity are also studied, by calibrating two different types of accelerometers, a piezoelectric one and a capacitive one, to check their effect on the accuracy of the methods under comparison. The reproducibility of methods is demonstrated. Relative uncertainty of methods ranges from 3 to 5 %, depending on the complexity of the model and of the requested operations. The results appear promising for low-cost calibration of new tri-axial accelerometers of MEMS type.

1 January 2016 in Measurement
Verified
Journal Article
Closed access
GDG. D’emilia
G. D’emilia
Antonella GaspariAntonella Gaspari
Antonella Gaspari
Emanuela NataleEmanuela Natale
Emanuela Natale

23 May 2019 in Journal of Sensors and Sensor Systems
Verified
Journal Article
Open access
PDF file
Giulio D'EmiliaGiulio D'Emilia
Giulio D'Emilia
Antonella GaspariAntonella Gaspari
Antonella Gaspari
Emanuela NataleEmanuela Natale
Emanuela Natale
A method for amplitude–phase calibration of tri-axial accelerometers in the low-frequency range (0 to 20 Hz) is proposed, based on a linear slide, used to excite all the axes of the accelerometer at the same time, and a laser Doppler vibrometer (LDV) as a reference. For the phase evaluation different methods, like cross-correlation analysis and cross-spectrum analysis, have also been used for validation purposes. The procedure includes many further validation actions in order to verify the correctness of modelling of the systems being tested, of the data processing and to reduce the calibration uncertainty. Results show that the phase is a critical aspect to consider in calibration, more than the amplitude, and the comparison with the theoretical model is useful to verify the hypotheses. Different behaviours result depending on the elements of the measurement chain and not only on the type of accelerometer.

23 December 2015 in ACTA IMEKO
Verified
Journal Article
Closed access
GDGiulio D'Emilia
Giulio D'Emilia
AGAntonella Gaspari
Antonella Gaspari
Emanuela NataleEmanuela Natale
Emanuela Natale
In this paper a methodology concerning the static and dynamic calibration of three-axis low-cost accelerometers in the (0 to 10) Hz frequency range is described, to be used for evaluation of existing civil infrastructures. Main and cross sensitivities of the accelerometers have been experimentally estimated by means of the matrix sensitivity concept. The standard deviation of accelerations obtained along all three axes using different calibration data sets in repeatability conditions has been calculated and intended as dynamic calibration uncertainty. The method has been validated by using reference accelerations accurately realized, in order to evaluate the residual bias error. Static and dynamic calibration test benches have been used to realize reference accelerations. In order to create a three-axis acceleration field, a mechanical arm is used in static calibration; a rotary device is used in order to test the accelerometers in dynamic conditions. According to the procedure described in this paper, a great improvement of the low cost accelerometers' metrological characterization could be achieved, especially in dynamic working conditions.