CO2 flooding is an important method for improving oil recovery for reservoirs with low permeability. Even though CO2 could be miscible with oil in regions nearby injection wells, the miscibility could be lost in deep reservoirs because of low pressure and the dispersion effect. Reducing the CO2–oil miscibility pressure can enlarge the miscible zone, particularly when the reservoir pressure is less than the needed minimum miscible pressure (MMP). Furthermore, adding intermediate hydrocarbons in the CO2–oil system can also lower the interfacial tension (IFT). In this study, we used dead crude oil from the H Block in the X oilfield to study the IFT and the MMP changes with different hydrocarbon agents. The hydrocarbon agents, including alkanes, alcohols, oil-soluble surfactants, and petroleum ethers, were mixed with the crude oil samples from the H Block, and their performances on reducing CO2–oil IFT and CO2–oil MMP were determined. Experimental results show that the CO2–oil MMP could be reduced by 6.19 MPa or 12.17% with petroleum ether in the boiling range of 30–60 °C. The effects of mass concentration of hydrocarbon agents on CO2–oil IFT and crude oil viscosity indicate that the petroleum ether in the boiling range of 30–60 °C with a mass concentration of 0.5% would be the best hydrocarbon agent for implementing CO2 miscible flooding in the H Block.
Geothermal power generation employing Organic Rankine Cycle (ORC) technology is a widely acknowledged and conventional approach for harnessing geothermal energy. In an innovative advancement, we propose a novel design integrating downhole thermoelectric power generation with a coaxial borehole heat exchanger. This design aims to enhance the efficiency and sustainability of geothermal energy utilization. In this innovative design, the geothermal well is divided into two distinct sections: a power generation section and a heat exchanging section, achieved through the implementation of a packer positioned from the uppermost part of the targeted zone. The process involves the injection of cold fluid downhole via an insulated pipe. Subsequently, a portion of the injected fluid is directed to flow in reverse within the casing-tubing annulus above the packer, while another portion circulates into the casing-tubing annulus below the packer before ascending through the tubing. This dual flow mechanism establishes distinct cold and hot sources for the thermoelectric generator, a key feature facilitated by this innovative design. Analytical models detailing of downhole temperature distribution for thermoelectric power have been meticulously developed. A comprehensive case study, focusing on a geothermal well with 3000 m length of power generation section and 500 m heat exchanging section, has been conducted. The results indicate that a significant generating capacity could be achieved with a higher wellhead temperature, and the payback period under different carbon tax scenarios is about 6–8 year. Furthermore, the effects of injection rate, fluid diversion ratio, and casing-tubing configuration on power performance and thermal-electricity efficiency are also discussed. This method not only enables the concurrent harvesting of geothermal energy and power generation but also operates consistently throughout the year. The results thus emphasize the viability and economic feasibility of the proposed approach.
Hydraulic fracturing is key to enhancing the productivity of shale and tight hydrocarbon reservoirs, as well as geothermal resources from hot dry rock. Assessing the range and efficiency of hydraulic fracturing is very important for onsite fracturing operations and decision making on subsequent fracturing plans and well-pattern deployment. The idea of injecting fluid mixed with magnetic material into a formation to detect subterranean structure has been considered for a long time. The detectability of the characteristics of propped fractures using magnetic field measurement is discussed and evaluated with an analytical model. The magnetic proppants synthesized with superparamagnetic nanoparticles should be “silent” during injection and could be activated by an external current. By measuring the magnetic field before and after the fracture was created and the magnetic proppants were magnetized, the magnetic anomalies can be obtained. The result indicates that the magnetic field caused by a fracture filled with magnetic proppants is very weak, so that magnetometers with higher precision and resolution should be used to capture such subtle signal. The higher susceptibility contrast of the magnetic nanoparticles is, the stronger external magnetic induction field could be detected. It is suggested that the superparamagnetic nanomaterial with effective magnetic susceptibility contrast of greater than 0.4–0.5 should be used for fracture monitoring in deep wells. To infer the fracture characteristics with the magnetic anomaly, the ground and adjacent wells’ monitoring practices are recommended.
26 March 2020 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Creating a good fracture network in hot dry rocks is the key to the success of an Enhanced Geothermal Systems project. Instead of creating large-scale fractures, the proposed thermal stimulation method has clear advantages by generating small-scale cracks, increasing crack density, and forming fracture networks in tight rocks. Granite samples from a tight formation in Lijin County in China were thermally treated at various temperatures to evaluate the permeability enhancement and the feasibility of thermal stimulation. Scanning electron microscope (SEM) method was also used to investigate the changes in interior structure in granite rocks. The experiments show that the threshold temperature of Lijin granites is around 300°C, the permeability can improve approximately 2 orders and the porosity can increase more than 5 times when heating over 600°C. Both crack length and width increase about 10 folds under the experiment conditions, and the original mineral disappearance and new mineral generation were observed. Thermal cracking under high temperatures plays a key role in permeability and porosity enhancement. Numerical simulation results show that the heated zone is very limited if only heating in a borehole. To expand the affected zone and improve energy recovery, a new thermal stimulation method combining microwave excitation with proppants to heat inside hydraulic fractures is proposed and discussed.
Summary: The accurate measurement of dynamic water cut is of great interest for analyzing reservoir performance and optimizing oilwell production. Downhole water-cut measurement is a very challenging work. Moreover, the surface-measured water cut is a comprehensive indicator of commingled producing well and it is difficult to use this parameter to deduce the downhole water cut of each contributing layer. In this paper, we propose to use distributed fiber-optic acoustic sensing (DAS) technology for the classification of water-cut range. DAS can dynamically monitor the entire wellbore by “listening” to the acoustic signals during flow. A large number of laboratory experimental data from DAS have been collected and analyzed using wavelet time scattering transform and short-time Fourier transform (STFT). The extracted low-variance scattering feature, short time-frequency feature, and fusion feature (combination of two extracted features) were learned with backpropagation (BP) neural network, decision tree (DT), and random forest (RF) algorithm. Then, a classification method of water-cut range in oil-water flow was established with machine learning. Field DAS data were collected from two oil wells to verify the effectiveness of the proposed method. The classification accuracies for the vertical well (Well A) are 92.4% and 87.4% by DT and RF model, respectively. For the horizontal well (Well B), the average classification accuracy exceeds 90% for all three methods. Water shutoff measure was conducted in Well B, and an obvious water decrease was realized. The result shows that the fusion feature overweighs single feature in machine learning with DAS data. This study provides a novel way to identify downhole water-cut range and detect water entry location in horizontal, vertical, and deviated oil-producing wells.