Rogers Tusiime

Rogers Tusiime

State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Material Science and Engineering, Donghua University
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 March 2019 in Polymers
Verified
Journal Article
Open access
PDF file
Zeyu SunZeyu Sun
Zeyu Sun
LXLei Xu
Lei Xu
ZCZhengguo Chen
Zhengguo Chen
YWyuhao wang
yuhao wang
Rogers TusiimeRogers Tusiime
Rogers Tusiime
HZHui Zhang
Hui Zhang
Efficient enhancement of the toughness of epoxy resins has been a bottleneck for expanding their suitability for advanced applications. Here, polysulfone (PSF) was adopted to toughen and modify the epoxy. The influences of PSF on the mechanical and thermal properties of the epoxy resin were systematically studied by optical microscopy, Fourier transform infrared spectrometer (FT-IR), differential scanning calorimetry (DSC), thermogravimetric analyzer (TG), dynamic mechanical thermal analyzer (DMA), mechanical tests and scanning electron microscope (SEM). The dissolution experimental results showed that PSF presents a good compatibility with the epoxy resin and could be well dissolved under controlled conditions. The introduction of PSF was found to promote the curing reaction of the epoxy resin without participating in the curing reaction and changing the curing mechanism as revealed by the FT-IR and DSC studies. The mechanical properties of PSF/epoxy resin blends showed that the fracture toughness and impact strength were significantly improved, which could be attributed to the bicontinuous phase structure of PSF/epoxy blends. Representative phase structures resulted from the reaction induced phase separation process were clearly observed in the PSF/epoxy blends during the curing process of epoxy resin, which presented dispersed particles, bicontinuous and phase inverted structures with the increase of the PSF content. Our work further confirmed that the thermal stability of the PSF/epoxy blends was slightly increased compared to that of the pure epoxy resin, mainly due to the good heat resistance of the PSF component.

1 February 2020 in Composites Part A: Applied Science and Manufacturing
Verified
Journal Article
Closed access
CCChao Cheng
Chao Cheng
ZCZhengguo Chen
Zhengguo Chen
ZHZhuang Huang
Zhuang Huang
CZChenyu Zhang
Chenyu Zhang
Rogers TusiimeRogers Tusiime
Rogers Tusiime
HZHui Zhang
Hui Zhang

1 October 2020 in Composites Communications
Verified
Journal Article
Closed access
ZCZhengguo Chen
Zhengguo Chen
JLJie Luo
Jie Luo
ZHZhuang Huang
Zhuang Huang
CCChaoqian Cai
Chaoqian Cai
Rogers TusiimeRogers Tusiime
Rogers Tusiime
JYJianyong Yu
Jianyong Yu

1 July 2021 in Ceramics International
Verified
Journal Article
Closed access
ZLZhang Lusha
Zhang Lusha
TZTang Zicheng
Tang Zicheng
Rogers TusiimeRogers Tusiime
Rogers Tusiime
WSWang Shaofei
Wang Shaofei
FNFeng Ningning
Feng Ningning
LYLiu Yong
Liu Yong

6 June 2019 in Polymers
Verified
Journal Article
Open access
PDF file
JLJianxiao Lu
Jianxiao Lu
CSChuanyue Sun
Chuanyue Sun
KYKexin Yang
Kexin Yang
KWKaili Wang
Kaili Wang
YJYingyi Jiang
Yingyi Jiang
MYMuhuo Yu
Muhuo Yu
Polylactic acid (PLA) is one of the most promising bio-based materials, but its inherent hydrophobicity limits its application. Although nanocellulose (NCC) is a desirable reinforcement for PLA, the poor interface compatibility between the two has been a challenge. In this work, hydroxyapatite (HAP) modified NCC was prepared, and the obtained NCC/HAP reinforcement was used to prepare PLA/NCC-HAP composites. Different ratios of NCC to HAP were studied to explore their effects on the mechanical and thermodynamic properties of the composites. When the ratio of NCC to HAP was 30/70, the tensile strength and tensile modulus of the composite film reached 45.6 MPa and 2.34 GPa, respectively. Thermogravimetric analysis results indicate that thermal stability of the composites was significantly improved compared with pure PLA, reaching 346.6 °C. The above revelations show that NCC/HAP significantly improved the interface compatibility with PLA matrix.

29 October 2022 in Composites Part B: Engineering
Verified
Journal Article
Closed access
JLJiamei Luo
Jiamei Luo
XYXueqin Yang
Xueqin Yang
YXYi Xue
Yi Xue
CYChenxi Yang
Chenxi Yang
ZYZehao Yang
Zehao Yang
JYJianyong Yu
Jianyong Yu