The tribo-characteristics of metal forming at high temperatures have not yet been well understood due to the complex nature of thermal, microstructural, interaction, and process parameters. This is a review paper on the effects of temperature, coating, and lubrication to the tribological characteristics in hot forming as well as the tribometers for different metal forming processes at elevated temperatures mainly based on the experimental work. The tribological behaviors of oxides in hot forming, such as rolling and stamping, were reviewed and presented. Some commonly used surface coatings and lubricants in hot forming were given. Many types of tribometer were selected and presented and some of them provided a great potential to characterize friction and wear at elevated temperatures. Nevertheless, more testing conditions should be further investigated by developing new tribometers. Eventually, experimental results obtained from reliable tribometers could be used in theory and model developments for different forming processes and materials at high temperatures. The review also showed the great potential in further investigations and innovation in tribology.
1 June 2009 in International Journal of Machine Tools and Manufacture
The in-service life of ASTM A36 welded steel pipes in power plants is often shortened by ash corrosion. During the heating condition, the ash deposition on the welded steel pipes gradually reduces the thickness of the pipes, thus, reducing the lifetime. Instead of replacing the pipes with new ones, the cost could be significantly reduced if the lifetime could be further extended. Weld cladding was the method selected in this study to temporarily extend the service life of welded pipes. This paper performed the mechanical investigations of A36—A36 welded steel plates after coating the surfaces with 309L stainless steel with a cladding method. The residual stress was also tested to observe the internal stresses developed during the welding processes of A36—A36 specimens. The comparison between the coated and non-coated surfaces of welded steels was performed by using the tensile tests (at room and elevated temperatures), corrosion (pitting corrosion, intergranular corrosion, and weight-loss corrosion) tests, and wear (shot blasting) tests. The life-extension of both coatings was evaluated based on the tensile tests and the corrosion and wear tests provided the qualitative evaluations of the coating performance. The results showed that surfaces coated by cladding could be used to temporarily extend the life of ASTM A36 welded steel under the studied conditions.
This paper presents two tooling-integrated sensing techniques for the in situ measurement and analyses of pressure distribution at the tool–workpiece interface and material draw-in during the stamping processes. Specifically, the contact pressure distribution is calculated from the measurements by an array of force sensors embedded in the punch, whereas sheet draw-in is measured by custom-designed thin film sensors integrated in the binder. Quantification of the pressure distribution from spatially distributed sensors has been investigated as a regularization problem and solved through energy minimization. Additionally, a Bayesian framework has been established for combining finite-element analysis (FEA) based estimates of the pressure distribution with experimentally measured evidence, to achieve improved spatiotemporal resolution. A new data visualization technique termed pressure and draw-in (PDI) map has been introduced, which combine spatiotemporal information from the two sensing techniques into an illustrative representation by capturing both the tool–workpiece interaction (dynamic information) and resulting workpiece motion (kinematic information) in a series of time-stamped snap shots. Together, the two separate yet complementary process-embedded sensing methods present an effective tool for quantifying process variations in sheet metal stamping and enable new insight into the underlying physics of the process.
The precision and accuracy of the final geometry in micro-parts is crucial, particularly for high-value-added metallic products. Micro-extrusion is one of the most promising processes for delivering high-precision micro-parts. The curving tendency observed in micro-extrusion parts is a major concern, significantly affecting the final part geometry. The purpose of this paper was to investigate the driving mechanism behind the curvature in micro-extrusion at room temperature. A finite element (FE) simulation was carried out to observe the influential primary factors: (1) grain size, (2) grain boundary, (3) grain orientation, and (4) bearing length of a 6063 aluminum alloy. The Extrusion Curvature Index (ECI) was also established to indicate the level of curvature in micro-extruded parts. The results showed that the grain boundary at the high strain and die opening area was the dominant factor for single-grain conditions. The interactive effects of the grain boundary and grain orientation also affected the curvature under single-grain conditions. If the number of grains across the specimen increased up to 2.7 (poly-grains), the curvature effect was dramatically reduced (the pins were straightened). For all conditions, the curvature in micro-extrusion could be eliminated by extending the bearing length up to the exit diameter length.