To optimise a tidal energy conversion system, the operation, maintenance and power generation aspects have to be taken into account. As a result the key focus of this study is to propose and investigate an alternative method of implementing a tidal energy conversion system using a pitch‐regulated turbine and a variable‐speed squirrel cage induction generator with long distance converters. The generator power output can be optimised by utilising variable‐speed control strategies allowing the system to operate at maximum power coefficient while availability can be increased by reducing the components installed offshore by using long three‐phase cables between the generator and onshore voltage source converters. The tidal current energy conversion system is investigated by developing a full resource‐to‐grid model in MATLAB/SIMULINK and by performing system analysis regarding the effects of harmonics in the long subsea cables. Simulation results show that optimised filter design and the choice of suitable operating frequency for the generator controller can minimise the overvoltages associated with the harmonics and the reflecting voltage waves in the cables.
Current developments in wave energy conversion have focused on locations where the wave energy resource is the highest; using large devices to generate hundreds of kilowatts of power. However, it is possible to generate power from low power waves using smaller wave energy devices. These lower rated wave energy converters can form arrays to supply power to remote coastal or island communities which are off‐grid. This study introduces wave‐to‐wire modelling of wave energy arrays for off‐grid systems using low power permanent‐magnet linear generators (PMLGs). Offshore energy storage at the DC link is added to keep the voltage constant along with a current controller for the inverter in order to supply constant low harmonic power to the residential load connected off‐grid. Simulation results produced in MATLAB/Simulink environment show that the wave energy array can generate power independently from the residential side by keeping the system stable using offshore storage. In addition, two different types of controllers for wave energy devices that use PMLGs are compared based on the power captured from the waves.
12 May 2015 in IEEE Transactions on Sustainable Energy
By moving the back-to-back ac-dc-ac converters in a tidal current conversion system (TCCS) onshore, maintenance requirements and cost are reduced significantly. This is because underwater components are not easily accessible and operate in a harsh environment. In addition to increased maintainability, the concept of long-distance controls offers maximum power capture from the tidal currents in the same way that a converter in the nacelle would offer. However, a number of challenges are associated with the concept of controlling electrical machines through long cables, which include electromagnetic traveling waves in the cables and system resonance. These phenomena can induce overvoltages at the generator terminals which can lead to system failure and high harmonics that can induce extra power losses. The major contribution of this paper is a new method of filter design for systems with long-distance controls and for minimization of system power loss. The proposed method is validated by developing a full resource-to-grid TCCS in MATLAB/Simulink. Simulation results show that using the proposed method, overvoltage mitigation can be achieved in the same way as literature-based filters, but at the same time, minimize the total system losses. The results from the analysis can be used to optimize tidal energy conversion systems with a similar electrical configuration.
The research presented in this paper investigates novel ways of optimizing all-electric wave energy converters for maximum wave-to-wire efficiency. In addition, a novel velocity-based controller is presented which was designed specifically for wave-to-wire efficiency maximization. In an ideal wave energy converter system, maximum efficiency in power conversion is achieved by maximizing the hydrodynamic efficiency of the floating body. However, in a real system, that involves losses at different stages from wave to grid, and the global wave-to-wire optimum differs from the hydrodynamic one. For that purpose, a full wave-to-wire wave energy converter that uses a direct-drive permanent magnet linear generator was modelled in detail. The modelling aspect included complex hydrodynamic simulations using Edinburgh Wave Systems Simulation Toolbox and the electrical modelling of the generator, controllers, power converters and the power transmission side with grid connection in MATLAB/Simulink. Three reference controllers were developed based on the previous literature: a real damping, a reactive spring damping and a velocity-based controller. All three literature-based controllers were optimized for maximum wave-to-wire efficiency for a specific wave energy resource profile. The results showed the advantage of using reactive power to bring the velocity of the point absorber and the wave excitation force in phase, which was done directly using the velocity-based controller, achieving higher efficiencies. Furthermore, it was demonstrated that maximizing hydrodynamic energy capture may not lead to maximum wave-to-wire efficiency. Finally, the controllers were also tested in random sea states, and their performance was evaluated.