Peter J. Joyce

Peter J. Joyce

orcid

Research Focus & Metrics

Academic Career Length

30Years (1997-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 1997 in Journal of Composite Materials
Verified
Journal Article
Closed access
PJPeter J. Joyce
Peter J. Joyce
DKDanielle Kugler
Danielle Kugler
TMTess J. Moon
Tess J. Moon
A technique has been developed, using optical microscopy, for the characterization of localized fiber waviness in composite laminates. Since most of the process-induced waviness which develops in unidirectional thermoplastic laminates is clearly discretized into little packets or fiber-wrinkled regions, the spatial distribution of fiber waviness can be estimated by surface inspection of the laminates. The waviness in these fiber-wrinkled regions is approximately sinusoidal so the waviness parameters chosen were amplitude and wavelength. The waviness in each of the fiber-wrinkled regions is approximately coherent; thus, one measurement of the local fiber geometry is enough to characterize the wave packet. Another issue this technique attempts to address is the thru-thickness waviness. To investigate the presence of waviness through the thickness a two pronged approach is presented: 1) a general survey in which an entire laminate was carefully sectioned into small pieces and inspected in cross-section for the existence of fiber waviness below the part surface and 2) a rigorous three-dimensional serial reconstruction of a "typical" fiber-wrinkled region to illustrate the nature of the fiber waviness in these zones. The laminates were surveyed using a statistical sampling routine and the fiber-wrinkled regions were carefully measured using microscopy and image analysis both on the surface and through the thickness of the plates. Results from a series of plates are included to demonstrate the application of this technique.

1 June 2004 in International Journal of Fracture
Verified
Journal Article
Closed access
PDF file
PJPeter J. Joyce
Peter J. Joyce
JJJames A. Joyce
James A. Joyce

1 September 1997 in Journal of Composite Materials
Verified
Journal Article
Closed access
DKDanielle Kugler
Danielle Kugler
PJPeter J. Joyce
Peter J. Joyce
TMTess J. Moon
Tess J. Moon
A detailed survey was conducted of the localized fiber waviness which develops in unidirectional thermoplastic laminates (T300/P1700) in order to determine how part length affects the distribution of fiber waviness. Eleven laminates of varying length were manufactured using identical processing histories. Each plate exhibited discrete wrinkle regions concentrated in the lengthwise center of the part. The amplitude, wavelength, and distribution of these regions were characterized for each plate processed, while penetration depths were studied for sample plates of each length. The results indicate that the waviness severity increases slightly with increasing part length. Furthermore, the major component is in-plane and the waviness frequently penetrates several plys below the surface.

27 January 2017 in Sensors
Verified
Journal Article
Open access
PDF file
RJR. Brian Jenkins
R. Brian Jenkins
PJPeter J. Joyce
Peter J. Joyce
DMDeborah Mechtel
Deborah Mechtel
Fiber Bragg grating (FBG) temperature sensors are embedded in composites to detect localized temperature gradients resulting from high energy infrared laser radiation. The goal is to detect the presence of radiation on a composite structure as rapidly as possible and to identify its location, much the same way human skin senses heat. A secondary goal is to determine how a network of sensors can be optimized to detect thermal damage in laser-irradiated composite materials or structures. Initial tests are conducted on polymer matrix composites reinforced with either carbon or glass fiber with a single optical fiber embedded into each specimen. As many as three sensors in each optical fiber measure the temporal and spatial thermal response of the composite to high energy radiation incident on the surface. Additional tests use a 2 × 2 × 3 array of 12 sensors embedded in a carbon fiber/epoxy composite to simultaneously measure temperature variations at locations on the composite surface and through the thickness. Results indicate that FBGs can be used to rapidly detect temperature gradients in a composite and their location, even for a direct strike of laser radiation on a sensor, when high temperatures can cause a non-uniform thermal response and FBG decay.

1 June 2012
Verified
Report
Open access
PDF file
DFDavid R. Forrest
David R. Forrest
IJIwona Maria Jasiuk
Iwona Maria Jasiuk
LBLloyd Brown
Lloyd Brown
PJPeter J. Joyce
Peter J. Joyce
AMAzzam Mansour
Azzam Mansour
LSLourdes Salamanca-Riba
Lourdes Salamanca-Riba
We characterized the chemical, thermophysical, and mechanical properties of nanomaterials with up to 5 wt% nanocarbon (aka covetics) in aluminum and copper metals. The nanocarbon is detectable by EDS and XPS but not by analytical methods such as LECO and GDMS. Nanocarbon raises the melting point and significantly alters surface tension, and thus porosity, during solidification. Open questions remain about the observation of higher density than would be predicted by the rule of mixtures. In aluminum alloys, we observed an increase in as-rolled strength and hardness with increasing amounts of nanocarbon. In copper, thermal conductivity was anisotropic: up to 50% higher in the extrusion direction and at least 25% lower in the transverse direction,and was different between transient and steady state test conditions. In aluminum, we observed a significant increase in electrical conductivity with nanocarbon, from 47 to 67% IACS. These materials are commercially promising because they are produced by conversion of inexpensive carbon powder to nanocarbon in the melt?paving the way for the production of nanomaterials in pyrometallurgical operations with economies of scale.

8 April 2013 in SAE International Journal of Advances and Current Practices in Mobility
Verified
Conference Paper
Closed access
PDF file
LHLeonard Hamilton
Leonard Hamilton
PJPeter J. Joyce
Peter J. Joyce
CFChris Forero
Chris Forero
MMMartin McDonald
Martin McDonald
A carbon-fiber-reinforced plastic (CFRP) monocoque racecar frame was designed and constructed by students for the 2012 Formula SAE (FSAE) collegiate design series competition. FSAE rules require that the monocoque frame have strength equal to or greater than the traditional steel space frames that they replace. The rules also specify minimum values for perimeter shear strength, main roll hoop attachment strength and driver harness attachment (pullout) strength. Overcoming limitations imposed by locally available finite element analysis tools, a variety of tests were devised to determine required laminate thicknesses and layup orientations. These included perimeter shear tests, pin shear tests, three-point bend tests and tensile tests. Based on the results of these tests, a sandwich construction using composite skins fabricated from carbon/epoxy prepreg and aluminum honeycomb core was selected. Starting from the outside, the sandwich consisted of a single layer of bi-directional woven carbon/epoxy, three unidirectional layers of carbon/epoxy, a single layer of bi-directional woven carbon/epoxy, 16-mm-thick aluminum honeycomb core, a layer of bi-directional woven carbon/epoxy, three unidirectional layers of carbon/epoxy and a final layer of bi-directional woven carbon/epoxy (F/0₃/F/core/F/0₃/F). Additional layers of carbon/epoxy weave were used in side impact regions and for various hard point attachments.Details of the mold design and manufacture as well as the composite lamination are summarized. The monocoque frame resulted in a 53% reduction in component weight and a 43% increase in torsional rigidity as compared to a steel space frame. The composite monocoque frame also provided a qualitative improvement in vehicle handling and aesthetics and more importantly proof that composite techniques suitable for the motorsports environment are achievable on an undergraduate level.