Energy consumption is directly related to the energy supply and production costs of gas-based direct reduction ironmaking, which is an effective choice to reduce the energy consumption of iron making. In this paper, the minimum Gibbs free energy principle was used to calculate the equilibrium composition under the conditions of reduction gas consisting of hydrogen and carbon monoxide (hydrogen concentration of 0–100%, reduction gas amount of 0–6.0 mol, reduction temperature of 790–1100 °C, and 0.5 mol Fe₂O₃). According to the enthalpy change, a simplified energy consumption model of a gas-based direct reduction ironmaking process was established, and the energy consumption per mole of metallic iron produced was calculated in detail. The following conclusions were drawn: at the stage when the reduction reaction occurred, the utilization rate of hydrogen or carbon monoxide remained unchanged with the increase in the amount of reduction gas or the increase in the hydrogen concentration of initial gas. The direct energy consumption increased with the increase in the hydrogen concentration at 790–980 °C and the opposite was true at 980–1100 °C. At 790–980 °C, the total energy consumption per ton of iron was greater than 0 and increased with the increase in initial hydrogen concentration from 40% to 100%, and it was less than 0 and increased with the increase in initial hydrogen concentration from 0% to 30%. It was possible to achieve zero total energy consumption with a hydrogen concentration of 30% and a 973 °C reduction.

The reduction gas used in the gas-based direct reduction iron-making process contains CH₄ in different concentrations, which has an important effect on the gas and heat needed for the reduction of iron oxide. To investigate the influence of CH₄ on gas utilization rate and heat needed at 900 °C, the initial conditions are set as H₂% + CO% = 90, CH₄% + N₂% = 10, gas pressure 1–9 atm, and 0.5 mol Fe₂O₃, and the equilibrium state composition is calculated using the minimum free energy method. The utilization rate of total gas can be improved, and gas demand can be decreased by increasing CH₄ concentration or H₂ concentration or reducing gas pressure. For the production of per ton of Fe from 25 °C to 900 °C, 6.08–7.29 m³ of reduction gas, and 7.338–8.952 MJ of gas sensible heat can be saved by increasing 1 m³ CH₄, while 10.959–11.189 MJ of reaction heat is increased. Compared with 3390.828–3865.760 MJ of the total heat of per ton of Fe for the reduction by H₂ + CO, 2.174–3.703 MJ of total heat is increased by increasing 1 m³ CH₄, and the increase ratio is 0.065–0.096%. This study is helpful to improve the gas efficiency and lower the pursuit of higher concentration of H₂ + CO in reduction gas.

In this paper, the precipitation thermodynamics and growth kinetics of TiN inclusions in GCr15 bearing steel during solidification were calculated in more detail. A more reasonable formula for calculating the segregation of the solute elements was adopted and the stability diagram of TiN precipitation considering solidification segregation was given. By solving equations, the change of the solute element content before and after TiN inclusion precipitation was calculated, and the results were substituted into the kinetic formula of the inclusion growth, which made the kinetic calculation more accurate. Results showed that the most effective way to reduce the precipitation of TiN is to increase the cooling rate and decrease the contents of Ti and N in steel. The effect of Ti content on the size of TiN inclusions is greater than that of N content.

Carbon included in coke and coal was used as a reduction agent and fuel in blast furnace (BF) ironmaking processes, which released large quantities of carbon dioxide (CO₂). Minimizing the carbon consumption and CO₂ output has always the goal of ironmaking research. In this paper, the reduction reactions of iron oxides by carbon, the gasification reaction of carbon by CO_2, and the coupling reactions were studied by thermodynamic functions, which were derived from isobaric specific heat capacity. The reaction enthalpy at 298 K could not represent the heat value at the other reaction temperature, so the certain temperature should be confirmed by Gibbs frees energy and gas partial pressure. Based on Hess’ law, the energy consumption of the ironmaking process by carbon was calculated in detail. The decrease in the reduction temperature of solid metal iron has been beneficial in reducing the sensible heat required. When the volume ratio of CO to CO₂ in the top gas of the furnace was given as 1.1–1.5, the coupling parameters of carbon gasification were 1.06–1.28 for Fe₂O₃, 0.71–0.85 for Fe₃O₄, 0.35–0.43 for FeO, respectively. With the increase in the coupling parameters, the volume fraction of CO₂ decreased, and energy consumption and CO₂ output increased. The minimum energy consumption and CO₂ output of liquid iron production were in the reduction reactions with only CO₂ generated, which were 9.952 GJ/t and 1265.854 kg/t from Fe₂O₃, 9.761 GJ/t and 1226.799 kg/t from Fe₃O₄, 9.007 GJ/t and 1107.368 kg/t from FeO, respectively. Compared with the current energy consumption of 11.65 GJ/t hot metal (HM) and CO₂ output of 1650 kg/tHM of BF, the energy consumption and CO₂ of ironmaking by carbon could reach lower levels by decreasing the coupled gasification reactions, lowering the temperature needed to generate solid Fe and adjusting the iron oxides to improve the iron content in the raw material. This article provides a simplified calculation method to understand the limit of energy consumption and CO₂ output of ironmaking by carbon reduction iron oxides.

In this study, high-purity iron with purity of 99.987 wt.% was prepared employing a process of direct reduction–melting separation–slag refining. The iron ore after pelletizing and roasting was reduced by hydrogen to obtain direct reduced iron (DRI). Carbon and sulfur were removed in this step and other impurities such as silicon, manganese, titanium and aluminum were excluded from metallic iron. Dephosphorization was implemented simultaneously during the melting separation step by making use of the ferrous oxide (FeO) contained in DRI. The problem of deoxidization for pure iron was solved, and the oxygen content of pure iron was reduced to 10 ppm by refining with a high basicity slag. Compared with electrolytic iron, the pure iron prepared by this method has tremendous advantages in cost and scale and has more outstanding quality than technically pure iron, making it possible to produce high-purity iron in a short-flow, large-scale, low-cost and environmentally friendly way.