Rihito Kuroda

Dr. Rihito Kuroda

Graduate School of Engineering, Tohoku University, 6-6-11-811, Aza-Aoba, Aramaki, Aoba-ku, Sendai, Miyagi 980-8579, Japan
orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 October 2012 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
YTYasuhisa Tochigi
Yasuhisa Tochigi
KHKatsuhiko Hanzawa
Katsuhiko Hanzawa
YKYuri Kato
Yuri Kato
RKRihito Kuroda
Rihito Kuroda
HMHideki Mutoh
Hideki Mutoh
SSShigetoshi Sugawa
Shigetoshi Sugawa
A 400H×256V pixels global-shutter high-speed CMOS image sensor including 128 on-chip memories/pixel has been fabricated in a 0.18-μm 2P4M CMOS with pinned photodiode process. The key technologies of this image sensor are as follows: multiple on-chip memories for each pixel, spatial separation of pixel and on-chip memory regions, multiple pixel output wires for each column, in-pixel noise reduction circuits, in-pixel source-follower current-sources and flexibly selectable on-chip memories. This CMOS image sensor achieves 1 Tpixel/s burst video operation, a full resolution of 10 Mfps with 128 frames and a half resolution of 20 Mfps with 256 frames, and 780 Mpixel/s continuous video operation on the same chip. The power consumption at 1 Tpixel/s was 24 W, while the image sensor operates without active cooling.

25 April 2022 in IEEE Transactions on Electron Devices
Verified
Journal Article
Open access
ITIsao Takayanagi
Isao Takayanagi
RKRihito Kuroda
Rihito Kuroda
Because of various purposes and high dynamic range (HDR) of brightness of objects in automotive applications, HDR image capture is a primary requirement. In this article, HDR CMOS image sensor (CIS) technology and its automotive applications are discussed including application requirements, basic HDR approaches and trends of HDR CMOS image sensor technologies, advantages and disadvantages for automotive application, and future prospect of the HDR technology. LED flicker caused by time aliasing effect and motion artifacts are two major issues in conventional multiple exposure HDR (MEHDR) approach, and several HDR technologies have been introduced for automotive applications. The advancements of image sensor fabrication technology, for instance, backside illumination (BSI) process and pixel level hybrid wafer bonding, have created new trends in the HDR technology.

19 January 2009 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
RKRihito Kuroda
Rihito Kuroda
TSTomoyuki Suwa
Tomoyuki Suwa
ATAkinobu Teramoto
Akinobu Teramoto
RHRui Hasebe
Rui Hasebe
SSShigetoshi Sugawa
Shigetoshi Sugawa
TOTadahiro Ohmi
Tadahiro Ohmi
Technology to atomically flatten the silicon surface on (100) orientation large-diameter wafer and the formation technology of an atomically flat insulator film/silicon interface are developed in this paper. Atomically flat silicon surfaces composed of atomic terraces and steps are obtained on (100) orientation 200-mm-diameter wafers by annealing in pure argon ambience at 1200degC for 30 min. Atomically flat surfaces with various terrace widths and step structures are observed by atomic force microscopy. It is found that the atomic terrace width changes widely with an off angle of the wafer surface from the (100) lattice plane. It is also found that the direction of the off angle significantly affects the atomically flat surface morphology, i.e., when the directions of the off angles are parallel to the directions, the step structure is composed of alternating pairs of straight and triangular steps. When the directions of the off angles are parallel to the directions, the step structure is composed of only straight steps. By precise control of the off angle and the direction toward the directions for a 200-mm-diameter silicon wafer, we have succeeded in fabricating an atomically flat surface with straight atomic steps and a very uniform terrace width of 140-150 nm on the entire surface of a large-diameter silicon wafer. Furthermore, it is found that only radical-reaction-based insulator film formation technology, such as oxidation utilizing oxygen radicals carried out at a low temperature (400degC ), preserves the atomic flatness of the insulator film/silicon interface. Finally, when MOSFETs are fabricated with an atomically flat interface, they exhibit near ideal subthreshold swing factors, with much smaller fluctuation, extremely lower 1/f noise, and higher MOS dielectric breakdown field intensity compared with MOSFETs fabricated with conventional technologies.

4 December 2020 in IEEE Transactions on Electron Devices
Verified
Journal Article
Open access
YFYasuyuki Fujihara
Yasuyuki Fujihara
MMMaasa Murata
Maasa Murata
SNShota Nakayama
Shota Nakayama
RKRihito Kuroda
Rihito Kuroda
SSShigetoshi Sugawa
Shigetoshi Sugawa
This article presents a prototype linear response single exposure CMOS image sensor with two-stage lateral overflow integration capacitors (LOFIC) exhibiting over the 120-dB dynamic range (DR) with 11.4 Me⁻ full well capacity (FWC) and maximum signal-to-noise ratio (SNR) of 70 dB. The measured SNR at all switching points were over 35 dB thanks to the proposed two-stage LOFIC.

26 May 2020 in Japanese Journal of Applied Physics
Verified
Journal Article
Open access
PDF file
KMKeiichiro Mori
Keiichiro Mori
SSShu-Ichi Samata
Shu-Ichi Samata
NMNoritomo Mitsugi
Noritomo Mitsugi
ATAkinobu Teramoto
Akinobu Teramoto
RKRihito Kuroda
Rihito Kuroda
SSShigetoshi Sugawa
Shigetoshi Sugawa
The surface roughness of silicon wafer is one of the most important issues that degrade characteristics of semiconductor devices. The importance of spatial roughness frequency as an influential parameter has been pointed. In this research, the effect of roughness frequency on MOSFET characteristics was studied using samples with different roughness for frequency. From the obtained results, it was found that roughness with a low spatial wavelength affects electron mobility and gate insulating film reliability such as E bd, Q bd and SILC.

29 May 2007 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
TOTadahiro Ohmi
Tadahiro Ohmi
ATAkinobu Teramoto
Akinobu Teramoto
RKRihito Kuroda
Rihito Kuroda
NMNaoto Miyamoto
Naoto Miyamoto
Current silicon technologies are now facing very severe standstill, i.e., the operation speed is strictly limited at a clock rate of about 3.8 GHz due to the limitation of the thinning of the gate insulator film thickness because of its large amount of leakage currents through the current thermal oxide films. This typical disadvantage of current silicon technologies has been completely overcome by introducing the newly developed radical-reaction-based semiconductor manufacturing instead of the current molecule-reaction-based semiconductor manufacturing, i.e., direct nitridation films such as Si3N 4 where the gate leakage current through the insulator films has been confirmed to be decreased by a factor of at least three orders of magnitude. The speed performance of silicon large-scale integrations is enhanced to exhibit a clock rate of more than 50 GHz by introducing the balanced complementary MOS on a silicon (551) surface substrate using 3-D-structured MOS transistors, where new key technologies must be introduced, namely: 1) direct nitridation gate insulator film Si3 N4 for 3-D MOS transistors; 2) atomic-order flat-gate insulator film/silicon interface; 3) drastically decreased series resistance of the source and drain electrodes by a factor of two orders of magnitude; and 4) introduction of the accumulation-mode MOS transistors instead of the inversion-mode MOS transistors