In this research, a new application of reduced graphene oxide (rGO) for a complementary metal-oxide-semiconductor (CMOS)-MEMS infrared (IR) sensor and emitter is proposed. Thorough investigations of IR properties including absorption and emission were proceeded with careful calibration and measurement with a CMOS thermoelectric sensor. The thermocouples of the sensor consist of aluminum and n-polysilicon layers which are fabricated with the TSMC 0.35 μm CMOS process and MEMS post-process. In order to improve the adhesion of rGO, a sensing area at the center of the membrane is formed with an array of holes, which is easy for the drop-coating of rGO material upon the sensing region. To evaluate the performance of the IR sensor with rGO, different conditions of the IR thermal radiation experiments were arranged. The results show that the responsivity of our proposed CMOS-MEMS IR sensor with rGO increases by about 77% compared with the sensor without rGO. For different IR absorption incident angles, the measurement of field of view shows that the CMOS-MEMS IR sensor with rGO has a smaller view angle, which can be applied for the application of long-distance measuring. In addition, characteristics of the proposed thermopile are estimated and analyzed with comparisons to the available commercial sensors by the experiments.
When using a MEMS sensor to measure the vacuum of a medium, the transition flow between the viscous flow and molar flow is usually used to describe the gas convection due to the physical principle, which is difficult to study through analysis and simulation. In this study, the description of gas flow under different pressures in a CMOS-MEMS vacuum sensors has been incorporated into a new behavioral ANSYS model. The proposed model was built and the characteristic parameters in the model were obtained based on a CMOS-MEMS thermopile patterned with circular symmetry and an embedded heater as a heat source. It contains a characteristic length to describe the effective distance of heat dissipation to the silicon substrate, and the corresponding transition pressure to describe the symmetrical phenomenon of gas heat conduction. The macro-model is based on the description of the physical characteristics of heat transfer and the characteristic parameters of the CMOS-MEMS vacuum sensor. The characteristic length of 49 μm and the corresponding transition pressure of 2396 mTorr for the thermoelectric-type vacuum sensor were extracted and verified successfully. The results show that the average error for the prediction of vacuum sensing by the macro-model we proposed is about 1.11%. This approach provides more applications for vacuum analysis. It can reduce the complexity of simulation and analysis and provide better simulation effects, including gas conduction mechanisms.
This paper introduces a thermoelectric-type sensor with a built-in heater as an alternative approach to the measurement of vacuum pressure based on frequency modulation. The proposed sensor is fabricated using the TSMC (Taiwan Semiconductor Manufacturing Company, Hsinchu, Taiwan) 0.35 μm complementary metal-oxide-semiconductor-microelectro-mechanical systems (CMOS–MEMS) process with thermocouples positioned central-symmetrically. The proposed frequency modulation technique involves locking the sensor output signal at a given frequency using a phase-lock-loop (PLL) amplifier to increase the signal-to-noise ratio (SNR) and thereby enhance the sensitivity of vacuum measurements. An improved first harmonic signal detection based on asymmetrical applied heating gives a precise measurement. Following calibration, the output voltage is in good agreement with the calibration values, resulting in an error of 0.25% under pressures between 0.1–10 Torr.
Superior to the traditional infrared temperature sensing architecture including infrared sensor and thermistor, we propose a novel sensing approach based on a single thermopile sensor with dual modes modulation. A switching and sensing circuit is proposed and realized with a chopper amplifier AD8551 and p-channel MOSFET (PMOS) for switching between detection of thermal radiation and the target and the ambient temperature for compensation. The error of target temperature after temperature compensation is estimated at less than 0.14 °C.
1 October 2019 in IOP Conference Series: Materials Science and Engineering
A new CMOS compatible thermopile was designed and fabricated with high fill factor, the floating membrane of the thermopile which we designed was formed by T-shape anisotropic etching window that never be proposed before. The design and fabrication of thermopile sensors are realized by using 1.2 mum CMOS IC technology combined with a subsequent anisotropic front-side etching. Four etching windows with minimum T-shape were opened by the CMOS processes, and then by using N 2 H 4 etching solution the silicon substrate was etched along directions. The T-shape etching windows which proposed in this paper are designed at four quadrant of membrane to form the extended undercut etching area of opened windows of overlap. The floating membrane has a larger area of 1100 times 1100 mum 2 and 2 mum thick. Therefore, the area of proposed membrane is increased greatly which absorbs more infrared radiation than the conventional design and enhances responsivity very well. A surface morphology measurement of thermopile is implemented to evaluate the influence of residual stress and characterize geometric shape of membrane practically. More careful analysis of surface morphology show the bending of suspension parts has a deviation of responsivity less than 0.167%. For our work, the T-shape structure of thermopile with large absorption area and high performance by using CMOS compatible process is proven to be very successful and easy fabricated