The motivation for this study is the fast development of floating offshore wind energy and the immature methodology and engineering practice related to predictions of vortex-induced motions (VIM). Benefiting from the oil and gas industry, in the past several decades, extensive knowledge and experience on vortex-induced vibrations (VIV) on slender marine structures has been gained. As the learnings from these efforts should be transferred and adapted to the renewable energy industry, a state-of-the-art review on influential VIM research has been carried out in this paper, focusing on: (1) engineering practice, (2) model tests, (3) numerical calculation, and (4) field measurement. Engineering gaps and potential research topics are identified as future work.

Slender marine structures such as deep-water riser systems are continuously exposed to currents, leading to vortex-induced vibrations (VIV) of the structure. This may result in amplified drag loads and fast accumulation of fatigue damage. Consequently, accurate prediction of VIV responses is of great importance for the safe design and operation of marine risers. Model tests with elastic pipes have shown that VIV responses are influenced by many structural and hydrodynamic parameters, which have not been fully modelled in present frequency domain VIV prediction tools. Traditionally, predictions have been computed using a single set of hydrodynamic parameters, often leading to inconsistent prediction accuracy when compared with observed field measurements and experimental data. Hence, it is necessary to implement a high safety factor of 10–20 in the riser design, which increases development costs and adds extra constraints in the field operation. One way to compensate for the simplifications in the mathematical prediction model is to apply adaptive parameters to describe different riser responses. The objective of this work is to demonstrate a new method to improve the prediction consistency and accuracy by applying adaptive hydrodynamic parameters. In the present work, a four-step approach has been proposed: First, the measured VIV response will be analysed to identify key parameters to represent the response characteristics. These parameters will be grouped by using data clustering algorithms. Secondly, optimal hydrodynamic parameters will be identified for each data group by optimisation against measured data. Thirdly, the VIV response using the obtained parameters will be calculated and the prediction accuracy evaluated. Last but not least, classification algorithms will be applied to determine the correct hydrodynamic parameters to be used for new cases. An iteration of the previous steps may be needed if the prediction accuracy of the new case is not satisfactory. This concept has been demonstrated with examples from experimental data.

Slender offshore structures in deep water subjected to currents may experience vortex-induced vibrations (VIV), which can cause significant fatigue damage. Extensive experimental researches have been conducted to study the VIV in the past several decades. However, most of the experimental works have small-scale models and relatively low Reynolds number (Re)—“subcritical” or even lower Reynolds number regime. There is a lack of full understanding of the VIV in prototype Re flow regime. Applying the results with low Re to a full-scale riser with prototype Re might have uncertainties due to the scaling effects. In addition, the surface roughness of the riser is also an important parameter, especially in critical Re regime, which is the case for prototype risers. In the present study, two full-scale rigid riser models with different surface roughness ratios were tested in the towing tank of MARINTEK in 2014. Stationary tests, pure crossflow (CF) free oscillation tests, and forced/controlled motion tests were carried out. Several conclusions could be made: The drag coefficient is dependent on the Re number and surface roughness ratio. At critical and supercritical flow regimes, the displacement amplitude ratio is less sensitive to Re than that at lower Re. The displacement amplitude ratio in subcritical flow regime is significantly larger than that in critical and supercritical flow regimes. Two excitation regions for the ‘smooth riser’ and one excitation region for the “rough riser” are identified.

Exploration of oil and gas in deep and ultra-deepwater under harsh weather condition is challenging. A steel lazy wave riser (SLWR) is considered to be a cost-effective alternative to get the gas or oil flow up to the platform under these conditions. The staggered buoyant section provides buoyancy force which forms an arch shape of the SLWR. This arch shape makes the SLWR configuration flexible and isolates the dynamic responses of the upper part and lower part of the riser. However, there is a lack of full understanding of the behavior of SLWRs. This is, due to a complicated loading from waves, vessel motions and flow induced vibrations caused by ocean currents, complex structural configurations, and non-linearities. Time-domain simulation is necessary to accurately predict the dynamic responses and capture the non-linearities. Realistic fatigue damage calculation is essential in the design phase of SLWR. The design of SLWR could be optimized with a better understanding of the dynamic responses of SLWR.

Marine drilling riser is subject to complicated environmental loads which include top motions due to mobile offshore drilling unit (MODU), wave loads, and current loads. Cyclic dynamic loads will cause severe fatigue accumulation along the drilling riser system, especially at the subsea wellhead (WH). Statoil and BP have carried out a comprehensive model test program on drilling riser in MARINTEK's Towing Tank in February 2015. The objective is to validate and verify software predictions of drilling riser behavior under various environmental conditions by the use of model test data. Six drilling riser configurations were tested, including different components such as upper flex joint (UFJ), tensioner, marine riser, lower marine riser package (LMRP), blow-out preventer (BOP), lower flex joint (LFJ), buoyancy elements, and seabed boundary model. The drilling riser models were tested in different load conditions. Measurements were made of microbending strains and accelerations along the riser in both in-line (IL) and crossflow (CF) directions. Video recordings were made both above and under water. In this paper, the test setup and test program are presented. Comparisons of results between model test and RIFLEX simulation are presented on selected cases. Preliminary results show that the drilling riser model tests are able to capture the typical dynamic responses observed from field measurement, and the comparison between model test and RIFLEX simulation is promising.

Vortex-induced vibrations (VIV) can lead to fast accumulation of fatigue damage and increased drag loads for slender marine structures. VIV responses mainly occur at the vortex shedding frequency, while higher harmonics can also be excited. Recent VIV model tests with flexible pipes have shown that higher harmonics in the crossflow (CF) direction can contribute to the fatigue damage significantly due to its higher frequency. Rigid cylinder experiments show that the CF third-order harmonics are more pronounced when the motion orbit is close to a “figure 8” shape and the cylinder is moving against the flow at its largest CF motion. However, there is still lack of understanding of when and where higher harmonics occur for a flexible pipe. Therefore, significant uncertainty remains on how to account for fatigue damage due to higher harmonics in VIV prediction. In the present paper, representative VIV data from various riser model test campaigns are carefully studied and analyzed. The key parameters that influence the magnitude of the third-order harmonic stress are found to be the bending stiffness, the reduced velocity, and the orbit stability. The experimental data are analyzed in order to assess the impact of each parameter on the third-order harmonic stress. A preliminary empirical response model to estimate the maximum CF third-order harmonic stress based on these identified structural and hydrodynamic parameters has been proposed. The results of this study will contribute to reduce the uncertainty and unnecessary conservatism in VIV prediction.