Thabo Falayi

Dr. Thabo Falayi

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 December 2019 in International Journal of Energy and Environmental Engineering
Verified
Journal Article
Open access
PDF file
TFThabo Falayi
Thabo Falayi
Fly ash (FA) and Basic oxygen furnace (BOF) slag were used to as additives in the geopolymerisation of gold mine tailings (GMT).The aim of the research was to determine the effects of the two additives on the strength formation and mechanism of metal immobilisation by modified GMT geopolymers. GMT, FA and BOF were mixed, respectively, and made into a paste with the addition of potassium hydroxide (KOH) before curing at various conditions. 50% replacement of GMT in the starting materials gave the highest unconfined compressive strength (UCS). The UCS for BOF-based geopolymer was 21.44 Mega Pascals (MPa), whilst the one for FA-based geopolymer was 12.98 MPa. The BOF-based geopolymer cured at lower temperature (70 °C) as compared to the FA-based geopolymer (90 °C). The optimum KOH concentration was 10 and 15 M for BOF- and FA-based geopolymers, respectively. BOF-based geopolymers resulted in the formation of calcium silicate hydrate (CSH) phases which contributed to higher strength; whereas in FA-based geopolymers, no new structures were formed. BOF-based geopolymers resulted in over 94% iron (Fe) immobilisation, whereas FA-based geopolymers had 76% Fe immobilisation. Fe immobilisation was via incorporation into the CSH or geopolymer structure, whilst other metal immobilisations were thought to be via encapsulation. 12-month static leaching tests showed that the synthesised geopolymers posed insignificant environmental pollution threat for long-term use.


1 August 2019 in Sustainable Environment Research
Verified
Journal Article
Open access
PDF file
TFThabo Falayi
Thabo Falayi
Ferrochrome (FeCr) slag was used as a precursor for the synthesis of a geopolymer. The effect of KOH concentration, liquid solid ratio (L/S), content of potassium metalisicate (KS) or potassium aluminate (KA), curing time on the unconfined compressive strength (UCS) and metal leachability of the synthesised geopolymer was investigated. A 10 M KOH and an L/S of 0.26 yielded a geopolymer with a UCS 13.0 MPa after 28 d of ambient temperature curing. A 0.125 wt KS:KOH addition yielded a geopolymer with a UCS of 14.7 MPa whilst a 1.25 wt KA:KOH addition yielded a geopolymer with a UCS of 24.5 MPa. The increase in strength was due to the formation of Calcium Silicate (Aluminate) hydrate. The aluminate activated FeCr slag geopolymer was the most competent of all geopolymers synthesised as it resulted in over 97% immobilisation of Fe, Zn, Mn, Ni and Cr. The 360-d static leachability tests for the aluminate activated geopolymer yielded a metal release rate lower than 90 mg mm− 2 of the geopolymer. The aluminate activated geopolymer also was resistant to changes in wet and dry cycles as it had a UCS reduction of 42% after 10 cycles whereas the pure FeCr slag geopolymer and the silicate activated geopolymer had a UCS reduction of 91 and 72% respectively after 10 cycles. The aluminate activated geopolymer met the minimum requirements for use as a paving brick for low traffic pavements. The study provides opportunities for sustainable use of FeCr slag with minimal environmental impact.

1 April 2021 in Journal of Water Process Engineering
Verified
Journal Article
Closed access
TLTumeletso Lekgoba
Tumeletso Lekgoba
FNFreeman Ntuli
Freeman Ntuli
TFThabo Falayi
Thabo Falayi

1 September 2022 in South African Journal of Chemical Engineering
Verified
Journal Article
Open access
MMMabatho Moreroa-Monyelo
Mabatho Moreroa-Monyelo
TFThabo Falayi
Thabo Falayi
FNFreeman Ntuli
Freeman Ntuli
NMNomampondo Magwa
Nomampondo Magwa

1 May 2019 in Proceedings of the Institution of Civil Engineers - Waste and Resource Management
Verified
Journal Article
Closed access
TFThabo Falayi
Thabo Falayi
In this study, acidic gold mine tailings were alkali activated using potassium hydroxide (KOH). The effect of potassium silicate (KS) and potassium aluminate (KA) on the strength and durability of the synthesised geopolymers was investigated. An optimisation experimental programme of various conditions was used to get the best geopolymers in terms of strength and metal leachability. A 1·1 mass/mass (m/m) potassium silicate : potassium hydroxide activation solution yielded a geopolymer with an unconfined compressive strength (UCS) of 9·94 MPa after curing for 5 d at 80ºC. A 2·8 m/m potassium aluminate : potassium hydroxide activation solution yielded a geopolymer with a UCS of 18·10 MPa after curing for 5 d at 100ºC. The potassium aluminate-based geopolymer was more durable for use as a backfill material as, after 10 wet and dry cycles, it had a UCS of 4·8 MPa whereas the potassium silicate-based geopolymer had a UCS of 1·23 MPa. The potassium aluminate-based geopolymer resulted in over 85% reduction in leachability of heavy metals from the cured geopolymer. This study showed that potassium aluminate activation of acidic gold mine tailings is an attractive route to stabilise/solidify hazardous material. The use of elevated temperature to achieve high strength for the geopolymer pales in comparison to the energy requirements of cement production.