In this study, we extend the pseudopotential lattice Boltzmann model proposed by Huang and Wu [ J. Comput. Phys. 327, 121 (2016)] to a three-dimensional model for practical simulations of multiphase flows with high density ratio. In this model, an additional source term is introduced into the evolution function, and the performed high-order Chapman-Enskog analysis demonstrates that the Navier-Stokes equations with accurate pressure tensor are recovered. Also, an alternative geometric formulation is developed to obtain various contact angles and an iteration scheme is involved in the initialization to improve the stability of the model. Theoretical and numerical investigations both validate that the thermodynamic consistency and tuning surface tension independently of density ratio is achieved through varying the two free parameters in the source term. Numerical simulations of droplet wetting indicate that a large degree range of contact angles can be precisely realized with the implementation of the wetting boundary scheme. Further dynamic examinations of droplet impingement on a thin film and a dry surface also verify the stability and capability of the proposed pseudopotential lattice Boltzmann model.

How to prevent the flushing-induced plume without changing people’s daily habits? Enlightened by thoughts of redesigning the restroom, this article provides a redesigned toilet using liquid-curtain-based strategy and verifies its advantages from the computational fluid dynamics. Two favorable effects are spotted: (1) the liquid curtain can suppress the upward virus particles (only 1% viruses can be lifted out of the toilet) and (2) the flow distribution caused by the liquid curtain can deliver virus particles into the sewage efficiently.

A model test system of horizontal slinky coil ground heat exchanger (HSCGHE) was established according to the similarity theory. A 2-D mathematical model of HSCGHE was built and experimentally validated. Experimental and numerical investigations of effects of different parameters on the thermal behavior of HSCGHE were undertaken. The results show that the heat release rate of the slinky coil and soil temperature around it increase as the inlet fluid temperature of coil increases. The soil temperature operated in intermittent mode can get a recovery, and thus the heat release rate of the coil can be improved effectively. For a given condition, reducing the coil central interval distance can increase the heat release rate of the HSCGHE, but also results in the decrease of the heat release rate per unit length of the coil. Therefore, the coil central interval distance cannot be decreased without limit. At the same time, the thermal performance of HSCGHE is related to the ground surface wind velocity. The heat release rate in the sandstone is the largest, followed by sand, the lowest for clay. Additionally, with the increase of buried depth of coil, the heat release rate increases, but the increase degree gradually becomes small. Thus, the buried depth cannot be too deep and should be determined by thermal performance, excavation cost and safety requirements.

The dynamic formation characteristics of droplets in a cross-junction can be captured via a high-speed image setup. The experimental results show four flow regimes: slug, dripping, jetting (threading and tubing), and viscous displacement. When Ca_d and Ca_c are small, the slug regime occurs. The dripping regime occurs when Ca_c is relatively high. The jetting regime appears when Ca_d increases to a considerable value. When Ca_c is much smaller than Ca_d, the viscous displacement regime occurs. In the slug and dripping regimes, the dispersed phase will experience growing, squeezing, and pinching off stages in the formation of droplets. These four flow regimes are strongly affected by Ca_c and Ca_d. In addition, the flow rates of the two phases can be changed to adjust the sizes of the generated droplet in the cross-junction under the slug regime and dripping regime. The dimensionless droplet length l* can be predicted via l* = (0.248 + 0.55Q)Ca_c^−0.203.

To provide further insight into humid air condensation on hybrid surfaces, an experiment was conducted to visually investigate the condensation process on wettability-interval grooved surfaces, which had hydrophobic ridges and hydrophilic grooves. The droplet dynamic behavior and heat transfer performance of condensation on a wettability-interval grooved surface were explored and compared with four other functional surfaces, including the plain hydrophilic surface, plain hydrophobic surface, hydrophilic grooved surface, and hydrophobic grooved surface. The presence of hydrophobic ridges perpendicular to the groove direction and hydrophilic grooves allowed for the exclusion and easy spreading of droplets, respectively. Compared with the other four functional surfaces, the coupling phenomena during condensation, i.e., the spontaneous suction and directional drainage via hydrophilic grooves, were only found on the wettability-interval grooved surface. These could not only remove condensate quickly but also suppress the formation of the flooded liquid film, which was beneficial to the enhancement of heat transfer performance. It was proven by the experimental results that at subcooling 12 K, the condensation heat flux on the wettability-interval grooved surface reached 1280 W/m², which was 1.25 times that of the plain hydrophobic surface (1030 W/m²), and 15% higher than that of the hydrophobic grooved surface (1110 W/m²). This indicated that the wettability-interval microgrooves could effectively enhance humid air condensation heat transfer performance.