Exploiting wind energy, which is a complex process in urban areas, requires turbines suitable for unfavorable weather conditions, in order to trap the wind from different directions; Savonius turbines are suitable for these conditions. In this paper, the effect of overlap ratios and the position of blades on a vertical axis wind turbine is comprehensively investigated and analyzed. For this purpose, two positive and negative overlap situations are first defined along the X-axis and examined at the different tip speed ratios of the blade, while maintaining the size of the external diameter of the rotor, to find the optimum point; then, the same procedure is done along the Y-axis. The finite volume method is used to solve the computational fluid dynamics. Two-dimensional numerical simulations are performed using URANS equations and the sliding mesh method. The turbulence model employed is a realizable K-ε model. According to the values of the dynamic torque and power coefficient, while investigating horizontal and vertical overlaps along the X- and Y-axis, the blades with overlap ratios of HOLR = +0.15 and VOLR = +0.1 show better performances when compared to other corresponding overlaps. Accordingly, the average C_m and C_p improvements are 16% and 7.5%, respectively, compared to the base with a zero overlap ratio.

In this paper, a pitch point absorber wave energy converter (WEC) is selected in order to be optimized for the wave characteristics of the Caspian Sea. The optimization process is a multi-objective optimization. For achieving the optimal WEC, mean absorbed power should be maximized while the construction cost should be minimized. The submerged surface area of the WEC is selected as a cost parameter. The amount of mean absorbed power depends on the installation site and also the shape of the WEC. For optimizing the shape of the WEC, various shapes are considered which are categorized into three different sections. A multi-objective genetic algorithm is used for optimization of the model, and the NEMOH software is used to simulate the wave-body interaction. The results show that the bottom flat and upside chamfered geometry with X:Y ratio of 10:1 is the best geometry for the desired application. Comparing the results from the final optimized shape with the optimized basic parallelepipedic hull shape reveals that much more extractable power can be achieved with less cost.

Performance investigation of oil journal bearings is of particular importance given the growing use of them as a support for rotary components in a wide range of industrial machines. Frictional forces and shear stresses, which are proportionate to the velocity of lubricating layers at different points in the bearing space, provide the basis for changing temperature conditions. Various factors such as rotational velocity increase, slip width reduction, and small heat transfer coefficient of lubricant cause intensification of lubricant temperature changes. In the present study, with using computational fluid dynamic (CFD) thermohydrodynamic (THD) numerical simulations, the effect of nanoparticles on the performance features of plain journal bearings is evaluated. Particularly, 3D simulation of a journal bearing is implemented using CFD which considerably improves the accuracy of results, coupled with conjugate heat transfer model for metal parts of bearings. Reynolds equation model is used to calculate the oil-film pressure developed in hydrodynamic journal bearings by applying the nano-based lubricants. The configuration of thrust bearing consists of six pads in this study. In order to reduce the modeling complexity and computational cost and because of the symmetrical geometry of the pads, simulation of a single pad is considered instead of the entire domain. In this study, TiO₂ nanoparticle with different volume fraction percentages are used. The parameters that are changed to evaluate the performance of the bearing include volume fraction percentage of the nanoparticle, type of lubricant, and rotational speed. Based on the results, for all different lubricant types, the dissipation power, average shear stress, and temperature rise are increased with augmenting the rotational speed. By increasing the rotational speed from 500 to 1500 rpm, the average shear stress increases by more than 100%, 120%, and 130% for DTE 26, DTE 25, and DTE 24 lubricant types, respectively. Moreover, by increasing the rotational speed from 500 to 1500 rpm, the dissipation power, and temperature rise are increased around 600% and 800%, respectively. Furthermore, increasing nanoparticles volume fraction from 0% to 10%, increases all parameters by approximately 10% for all lubricant types and in all rotational speeds.

Subcooled flow boiling is one of the major issues in the nuclear and power generation industries. If the fluid inlet temperature in the boiling area is less than the boiling temperature, the boiling process is called subcooled boiling. The symmetry of a physical system is a constant property of the system and is fixed by deformation. Using magnetohydrodynamic (MHD) forces and broken symmetry induced by nanosized particles, fluid and thermal systems can be more controlled. In this study, the effect of a magnetic field and nanoparticles on subcooled flow boiling in a vertical tube was investigated. For this purpose, a one-dimensional numerical code was used to simulate the flow and variations of various parameters that have been investigated and evaluated. The results showed that as the flow entered the heated area, the vapor volume fraction, Froude number, fluid cross-sectional area forces, mixture velocity, fluid velocity, bubble departure diameter, liquid and vapor Reynolds numbers, squared ratio of the Froude number to the Weber number, and fluid cross-sectional area forces coefficient increased. In the same region, the Eötvös number, root mean square (RMS) of the fluid cross-sectional area force, sound velocity, liquid superficial velocity, critical tube diameter, bubble departure frequency, and density of the active nucleation site were reduced. It was also observed that after the heated area and under the influence of the magnetic field and the nanoparticles, the values of the vapor volume fraction, Froude number, fluid cross-sectional area force, mixture velocity, fluid velocity, vapor, liquid Reynolds number, and squared ratio of the Froude number to the Weber number were decreased. Moreover, there was no significant effect on the Eötvös number, liquid superficial velocity, Taylor bubble Sauter mean diameter, bubble departure diameter, critical tube diameter, bubble departure frequency, or density of the active nucleation site.