The thermal bow of the rotor occurs in the cooling process after the shutdown of the aeroengine. The deflection of the bowed rotor is the primary concern of the research on this problem. The objective of this work is to propose a method to predict the bow shape of the rotor with the measured temperature and displacement in a rotor thermal bow experiment. The experiment was introduced and the variations of the measured temperature and displacement were analyzed. A series of polynomial function was proposed to model the bowed shape of the rotor. The measured temperature and displacement were taken into considered in the constraint equations, with which the coefficients in the polynomial function were obtained. The bow shapes of the rotor at different time in the experiments were analyzed. Results showed that the maximum deflection of the rotor was much greater than the measured displacement at the sections near the rotor support. The forced cooling could reduce the thermal deflection of the rotor quickly. The analysis of the different cases of experiment indicated that the proposed method could predict the bow shape of the rotor with the measured temperature and displacement.
25 February 2013 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
In this article, a study of elastic–plastic contact of statistical rough surfaces is presented. The contact behaviors of a single asperity with deformable substrate are studied by finite element method. The influences of material properties and substrate deformation on the single asperity contact behaviors are investigated. An elastic–plastic contact model of rough surfaces is established based on the proposed single asperity contact model and statistical rough surface contact model. The surface topography plasticity index and material plasticity index are defined to indicate the influences of surface topography and material properties on the contact behaviors of rough surfaces. Comparisons with some exiting models and finite element results show that the proposed formulations can model the single asperity contact behaviors well for a wide interference range. The rough surface contact model in this work is consistent with some existing models for small plasticity indices, and it is slightly different from the existing models for large plasticity indices. The increase of surface topography plasticity index and material plasticity index would result in larger contact area and contact load for given separations.
11 October 2012 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
The overall contact behavior of an elastic perfectly plastic hemisphere against a rigid plane is presented. Based on volume conservation, the upper limit of overall contact area is derived. A finite element model for the overall contact behavior of a hemisphere and a rigid plane is studied. The material of the hemisphere is assumed to be elastic perfectly plastic. A series of materials with different yield stress to elasticity modulus ratios are studied in finite element analysis. The axial movement of the deformed hemisphere base is prevented. The radial deformable and radial rigid boundary conditions of the hemisphere bottom base are considered. Results show that the overall contact area gradually deviates from Hertz solution, and approaches the upper limit with the increase of interference. Material yield stress to elasticity modulus ratio mainly influences contact behaviors in the early contact stage, while the boundary condition of hemisphere bottom base affects the contact behaviors significantly for large contact interferences. By incorporating some existing models and fitting finite element results, a model for overall contact of a hemisphere against a rigid plane is obtained. This study covers the overall contact, which ranges from initial contact to the collapse of hemisphere. Comparisons of this study with several existing models and experimental data indicate that this study can predict the contact behaviors well in overall contact range.
12 November 2019 in Journal of Mechanical Science and Technology
The axial mechanical behaviors of the bolted joint are a primary concern of the bolted joint structures. The axial load position has obvious influence on the axial mechanical behaviors of the bolted joint with different materials, while it can not be considered by the analytical method yet. The objective of this work is to fill this gap. With the pressure cone assumption, the axial resilience of the stress zones is derived, and the detailed formulation of the load introduction factor is proposed. The mechanical behavior of the bolted joint subjected to external axial load is formulated and compared with finite element analysis. Results show that the distance between load planes has apparent influence on the axial mechanical behaviors of the bolted joint. In particular for the bolted joint with different materials, the axial positions of the external load have obvious effect on the mechanical behavior. Comparisons with the finite element results indicate that with the proposed formulation of load introduction factor, the analytical formulations could predict the mechanical behavior of the bolted joint with different materials accurately. The proposed formulation of load introduction factor in this work could be an effective supplement of the heavy duty bolt design guideline.