The influence of low temperature annealing and subsequent deformation on microstructure, strength and ductility was investigated for the first time for high pressure torsion (HPT) processed commercially pure Al. Extremely high increases in the conventional yield stress (up to 50%) and ultimate tensile strength (up to 30%) were obtained by annealing of the ultrafine grained (UFG) samples in the range 90-200 °C for 1 h. Such increases were accompanied by a sharp drop in ductility up to 1%. Implementation of high ductility at the level of coarse-grained Al, while maintaining high strength of the HPT-processed sample was demonstrated for the first time and achieved by repeating the low temperature annealing followed by subsequent additional HPT deformation. The key role of relaxation of non-equilibrium high-angle grain boundaries (GBs) in the strengthening effect of UFG-Al by annealing is shown. Two theoretical models are suggested to explain the hardening by annealing and the implementation of high ductility in UFG structures. Within the models, plastic deformation occurs through emission of lattice dislocations from triple junctions of GBs containing pile-ups of grain-boundary dislocations, glide of the lattice dislocations across neighboring grains, their accumulation at and climb along the opposite GBs. The energy characteristics and the critical stresses of dislocation emission are determined in two different cases, for UFG Al subjected to annealing only and to annealing with subsequent additional HPT deformation. The calculated theoretical dependences of the flow stress on the plastic deformation value well fit qualitatively and quantitatively to our experimental data.
The critical conditions have been calculated for the generation of circular prismatic loops of misfit dislocations at the interfaces in spherically symmetric composite core-shell nanoparticles. It has been shown that the formation of these loops becomes energetically favorable if the misfit parameter exceeds a critical value, which is determined by the geometry of the system. The most preferred position of the dislocation loop is in the equatorial plane of the nanoparticle. For a given radius of the nanoparticle, there is a minimum value of the critical misfit parameter below which the generation of a misfit dislocation is energetically unfavorable for any ratio of the core and shell radii. For a misfit parameter exceeding the minimum critical value, there are two critical values of the reduced radius of the particle core in the interval between which the generation of a dislocation loop is energetically favorable. This interval increases with increasing misfit parameter for a fixed particle size and decreases with decreasing particle size for a fixed misfit parameter.
1 December 2012 in International Journal of Engineering Science
The results of application of gradient theory of elasticity to a description of elastic fields and dislocation and disclination energies are considered. The main achievement made in this approach is t
A theoretical model has been proposed for describing the relaxation of misfit stresses in a spherically symmetric composite core-shell nanoparticle due to the generation and expansion of rectangular prismatic dislocation loops at the internal and external interfaces. The critical conditions of the formation of these loops have been calculated for nanoparticles consisting of a relatively massive core and a thin shell. It has been shown that the generation of dislocation loops is possible when the misfit of the lattice parameters of the core and shell of the nanoparticle exceeds a critical value that depends on the nanoparticle radius, the shell thickness, the loop formation position, and the shape of loops. This condition holds for a loop in the shell when the shell thickness either lies in a specific range of small values or (for a larger misfit) is less than a critical value. For the generation of loops in the core, the shell thickness should exceed a critical value. The dislocation loops elongated along the core-shell interface are formed more readily. As the shell thickness increases at a fixed nanoparticle radius, the energetically more favorable generation of a dislocation loop occurs first from the free surface into the bulk of the shell, then from the interface into the shell, and finally from the interface into the core of the nanoparticle.
[[abstract]]Micropipe bundling and twisting in SiC crystals was revealed using synchrotron x-ray phase sensitive radiography. The computer simulation of micropipe evolution during the crystal growth suggests that the bundled and twisted micropipes arise under the influence of stress fields from other neighboring micropipes. The annihilation of twisted dipoles is attributed to their transformation into semiloops. Reactions of micropipe coalescence lead to the generation of micropipes and/or the annihilation of initial micropipes, resulting in the decrease in their average density.[[fileno]]2060117010113[[department]]工程與系統科學