Yiming Jiang

Yiming Jiang


Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 March 2019 in Materials
Verified
Journal Article
Open access
PDF file
YTYiwei Tang
Yiwei Tang
NDNianwei Dai
Nianwei Dai
JWJun Wu
Jun Wu
YJYiming Jiang
Yiming Jiang
JLJin Li
Jin Li
The influence of surface roughness on the pitting corrosion behaviour of 2205 duplex stainless steel (DSS) in a chloride-containing environment was investigated using electrochemical noise (EN) techniques and morphology observation. A rougher surface condition increased the frequency of pit initiation because of the increase in more occluded pit sites. Rough surface finish also accelerated pit growth by increasing the actual dissolution rate in the pit. Metastable pits on rougher surfaces had longer lifetimes and grew to larger sizes, as their inner chemical environment was more easily maintained. However back-scatter images showed that pitting initiates on DSS 2205 regardless of the roughness condition.

28 September 2022 in Coatings
Verified
Journal Article
Open access
PDF file
ZDZhigang Di
Zhigang Di
SMShengjun Ma
Shengjun Ma
HWHuanhuan Wang
Huanhuan Wang
ZGZichao Guan
Zichao Guan
BLBingjie Lian
Bingjie Lian
YJYiming Jiang
Yiming Jiang
In this paper, high-performance silica aerogel (SiO2 aerogel) thermal insulation coatings were obtained and profited from the excellent thermal insulation capability of SiO2 aerogel. The comprehensive properties and thermal insulation mechanism of the coatings were investigated via Scanning Electron Microscope (SEM), Fourier Transform Infrared Spectroscopy (FT-IR), contact angle, and temperature difference tests. Results showed that there was a contradiction between thermal insulation and mechanical property in this coating after the addition amount and proportion of silica aerogel, hollow glass microsphere, glass fibers, aqueous acrylic emulsion, and dispersing agents were optimized carefully. When the mass ratio of hollow glass to SiO2 aerogel microspheres was 1:1, the overall performance of the coating was the best with thermal conductivity of 0.050 W/(m·K) and adhesive strength of 1024 kPa.

29 April 2019 in Materials
Verified
Journal Article
Open access
PDF file
GLGuangming Liu
Guangming Liu
YLYuanyuan Liu
Yuanyuan Liu
YCYawen Cheng
Yawen Cheng
JLJin Li
Jin Li
YJYiming Jiang
Yiming Jiang
The intergranular corrosion (IGC) behavior of a new metastable austenitic Cr–Mn–Ni–N–Cu high-strength stainless steel under various heat treatments was studied. The samples were solution treated at 1050 °C for 30 min and then aged at 600 to 900 °C for 10 to 300 min, respectively. The IGC susceptibility of aged samples was investigated using a double-loop electrochemical potentiokinetic reactivation (DL-EPR) test in a solution of 0.1 M H2SO4 and 0.002 M KSCN and the 10% oxalic acid etch. The surface morphologies of samples were characterized using optical microscopy and the scanning electron microscopy after electrochemical tests. Two time-temperature-sensitization diagrams were plotted based on the DL-EPR test and oxalic acid etching. No IGC and precipitate were observed for samples aged at 600 °C and 900 °C. For samples aged at 650 °C to 750 °C, the IGC susceptibility and the amount of precipitate both increased with the extended aging time. For samples aged at 800 °C and 850 °C, the amount of precipitate increased as the aging time was prolonged. However, only the sample aged at 800 °C for 60 min showed slight intergranular corrosion in the DL-EPR test. The IGC of the Cr–Mn–Ni–N–Cu austenitic stainless steel originated from the precipitation of Cr23C6 and Cr2N at the grain boundaries. The chromium-depleted zones near grain boundaries stood as the corrosion nucleation sites, but the dissolution of the weak area followed a consistent crystallographic orientation along each grain boundary.

31 August 2012 in Steel Research International
Verified
Journal Article
Closed access
PDF file
XLXuyan Li
Xuyan Li
LGLifang Guo
Lifang Guo
DHDong Han
Dong Han
JLJin Li
Jin Li
YJYiming Jiang
Yiming Jiang

1 June 2021 in Materials Research Express
Verified
Journal Article
Open access
PDF file
YTYanliang Tan
Yanliang Tan
YSYangting Sun
Yangting Sun
LLLonglin Lei
Longlin Lei
YLYuanyuan Liu
Yuanyuan Liu
JLJin Li
Jin Li
YJYiming Jiang
Yiming Jiang
In this study, Sn2+ solution simulation method is used to investigate the effect of Sn on pitting corrosion behavior of tin-containing ferritic stainless steel 430LX. It is found that the correlation between Epit and [Sn2+] is opposite to the correlation between critical potential temperature (CPT) and [Sn2+]. After potentiostatic polarization at a specific potential, the correlations become the same. The CPT experiment after a series of potentiostatic steps proves that Sn2+ exhibits positive influence only when the pH and potential is within a certain range. All the complicated phenomena can be explained by the under-potential deposition mechanism. SnO2 passivation film that enhances the corrosion resistance is only produced when under-potential deposition occurs.

1 January 2012 in ACTA METALLURGICA SINICA
Verified
Journal Article
Closed access
LGLifang Guo
Lifang Guo
XLXuyan Li
Xuyan Li
TSTao Sun
Tao Sun
JXJuliang Xu
Juliang Xu
JLJin Li
Jin Li
YJYiming Jiang
Yiming Jiang