Polymer grafts were used to tailor the interphases between ZnO nanoparticles (NPs) and silicone matrices. The final electrical properties of the nanocomposites were tuned by the grafted interphases, by controlling the inter-particle distance and the NP-morphology. The nanocomposites can be used in electrical applications where control of the resistivity is desired. Hansen's solubility parameters were used to select a semi-compatible polymer for grafting to obtain anisotropic NP morphologies in silicone, and the grafted NPs self-assembled into various morphologies inside the silicone matrices. The morphologies in the semi-compatible nanocomposites could be tuned by steering the graft length of poly(n-butyl methacrylate) via entropic matrix-graft wetting using surface-initiated atom-transfer radical polymerization. Image analysis models were developed to calculate the radius of primary NPs, the fraction of aggregates, the dispersion, and the face-to-face distance of NPs. The dielectric properties of the nanocomposites were related to the morphology and the face-to-face distance of the NPs. The dielectric losses, above 100 Hz, for nanocomposites with grafted NPs were approximately one decade lower than those of pristine NPs. The isotropic nanocomposites increased the resistivity up to 100 times compared to that of neat silicone rubber, due to the trapping of charge carriers by the interphase of dispersed NPs and nanoclusters. On the other hand, the resistivity of anisotropic nanocomposites decreased 10–100 times when the inter-particle distance in continuous agglomerates was close to the hopping distance of charge carriers. The electrical breakdown strength increased for compatible isotropic nanocomposites, and the temperature dependence of the resistivity and the activation energy were ∼50% lower in the nanocomposites with grafted NPs. These flexible dielectric nanocomposites are promising candidates for low-loss high-voltage transmission cable accessories, mobile electronic devices, wearables and sensors.
Three stator bars were subjected to 1142 hours of thermoelectric aging. At intervals during this time, the aging of the insulation was investigated by capacitance (C) and dissipation factor (DF) measurements and by the physicochemical techniques of infrared spectroscopy (FTIR) and Differential Scanning Calorimetry (DSC). Results indicated different degradation paths under discharge conditions, where the volume of voids within the insulation played a major role. Postcuring reactions were predominant during the first aging cycles. Such reactions were detected as reductions in capacitance and dissipation factor parameters, as a depletion of the chemical group epoxide at the absorption band 909 cm-1 as measured by FTIR, and as an increase of the glass transition temperature (Tg) of the epoxy resin. Since the postcuring reactions occur globally in the insulation, they were detected by both dielectric and physicochemical techniques. With the advance of the aging program the epoxy resin underwent structural changes, seen as modifications of functional groups CH2, CH3 and C=O. The air atmosphere where partial discharges occurred also promoted the formation of reactive species. When the air volume was high enough, the findings of FTIR measurements suggested a local degradation mechanism of mica involving cation exchange reactions between partial discharge byproducts and potassium layers in the mica.
Wetting of water, a 1 : 1 water/ethanol mixture and an aqueous dodecylbenzene sulfonic acid surfactant solution on hydrophobic and superhydrophobic surfaces were studied using confocal Raman microscopy. The superhydrophobic surfaces were prepared by immersion of a glass substrate in a silica particle/fluoropolymer formulation followed by silanization. Preparation of hydrophobic surfaces was done in the same way with the exception that the silica particles were excluded from the formulation. The hydrophobic and superhydrophobic surfaces were characterized with respect to surface roughness using AFM, and by contact angle measurements using different liquids. Confocal Raman microscopy measurements in a 1 : 1 water/ethanol mixture showed an enrichment of ethanol close to the superhydrophobic surface, which could not be observed for the hydrophobic surface. Unexpectedly, the Raman spectrum of a pure water film in close proximity to the superhydrophobic surface displayed some differences compared to that of bulk water and indicated a stronger hydrogen-bonding close to the superhydrophobic surface. Evidence for capillary evaporation next to the superhydrophobic surface was also found, and this results in very long-range capillary attraction between one superhydrophobic surface and a hydrophobic colloidal probe as shown by AFM colloidal probe force measurements. Addition of a surfactant or ethanol suppresses capillary evaporation.
1 June 2015 in Journal of Colloid and Interface Science