Photothermal therapy can serve as an alternative to classic surgery in the treatment of patients with cancer. However, using photothermal therapy can result in local overheating and damage to normal tissues. Therefore, it is important to determine effective heating conditions based on heat transfer. In this study, we analyzed laser–tissue interactions in gold nanoparticle (GNP)-enhanced photothermal therapy based on the theory of heat transfer. The thermal behavior inside tissues during photothermal therapy was analyzed using numerical analysis. The apoptosis ratio was defined by deriving the area having a temperature distribution between 43 °C and 50 °C, which is required for inducing apoptosis. Thermal damage, caused by local heating, was defined using the thermal hazard value. Using this approach, we confirmed that apoptosis can be predicted with respect to tumor size (aspect ratio) and heating conditions (laser intensity and radius) in photothermal therapy with a continuous-wave laser. Finally, we determined the effective apoptosis ratio and thermal hazard value of normal tissue according to tumor size and heating conditions, thereby establishing conditions for inducing maximal levels of cell apoptosis with minimal damage to normal tissue. The optimization conditions proposed in this study can be a gentle and effective treatment option for photothermal therapy.
As the display industry continues to advance, various new materials are being developed for utilizing microtechnology and nanotechnology in display panels. Among these, transparent materials have been widely applied to the internal wiring of displays and flexible substrates, owing to their high optical transmittance, isotropy, and anisotropy. Thus, measurement of the thermophysical properties of various transparent materials is important. This study measured thermal conductivity by selecting quartz, a transparent isotropic material, and sapphire glass, a transparent anisotropic material, as measurement target materials using a rear-side photothermal deflection method. Measurements were made via a three-dimensional unsteady heat conduction equation, to which complex transformation was applied and numerically analyzed using COMSOL Multiphysics. Phase delays for a pump beam and a probe beam for a relative position were derived through a deflection analysis. From the derived phase delays between the numerical analysis and experimental result with optical alignment, the absolute and relative errors of quartz were appropriately confirmed to be 0.069 W/m-K and 5%, respectively, while those of the sapphire glass were likewise confirmed to be 0.55 W/m-K and 1.5%, respectively.
Transparent anisotropic materials have garnered attention along with the growth of the semiconductor and display industries. Transparent anisotropic materials have the characteristic of varying electrical, optical, and thermal properties based on their crystal orientation, and many studies are being conducted on this topic. In order to utilize transparent anisotropic materials properly, thermal properties such as thermal conductivity are essentially required. However, due to the limitations of the existing thermal property measurement methods for transparent anisotropic materials, it is difficult to provide the thermal properties of transparent anisotropic materials. To address this problem, a transparent anisotropic collinear method capable of measuring the effective thermal conductivity of a transparent anisotropic material according to its crystal orientation is proposed in this paper. To this end, the internal temperature distribution of a transparent anisotropic material and the phase delay of the probe beam were theoretically derived through a numerical analysis model that uses a three-dimensional heat conduction equation. This model was applied to anisotropic thermal conductivity with orthorhombic structure. To verify the proposed method of measuring the thermal conductivity of a transparent anisotropic material, the thermal properties of 3 mm-thick A-plane sapphire glass were measured and compared with those of the existing literature. It was confirmed that the absolute errors were less than about 4 W/mk.
Among the noncontact measurement technologies used to acquire thermal property information, those that use the photothermal effect are attracting attention. However, it is difficult to perform measurements for new materials with different optical and thermal properties, owing to limitations of existing thermal conductivity measurement methods using the photothermal effect. To address this problem, this study aimed to develop a rear-side mirage deflection method capable of measuring thermal conductivity regardless of the material characteristics based on the photothermal effect. A thin copper film (of 20 µm thickness) was formed on the surfaces of the target materials so that measurements could not be affected by the characteristics of the target materials. In addition, phase delay signals were acquired from the rear sides of the target materials to exclude the influence of the pump beam, which is a problem in existing thermal conductivity measurement methods that use the photothermal effect. To verify the feasibility of the proposed measurement technique, thermal conductivity was measured for copper, aluminum, and stainless steel samples with a 250 µm thickness. The results were compared with literature values and showed good agreement with relative errors equal to or less than 0.2%.