Fluorosurfactants are the most effective compounds to lower the surface tension of aqueous solutions, but their wetting properties as related to low energy hydrocarbon solids are inferior to hydrocarbon trisiloxane surfactants, although the latter demonstrate higher surface tension in aqueous solutions. To explain this inconsistency available data on the adsorption of fluorosurfactants on liquid/vapour, solid/liquid and solid/vapour interfaces are discussed in comparison to those of hydrocarbon surfactants. The low free energy of adsorption of fluorosurfactants on hydrocarbon solid/water interface should be of a substantial importance for their wetting properties.

The simultaneous spreading and evaporation of droplets of aqueous trisiloxane (superspreader) solutions onto a hydrophobic substrate has been studied both experimentally, using a video-microscopy technique, and theoretically. The experiments have been carried out over a wide range of surfactant concentration, temperature, and relative humidity. Similar to pure liquids, four different stages have been observed: the initial one corresponds to spreading until the contact angle, θ, reaches the value of the static advancing contact angle, θ_ad. Duration of this stage is rather short, and the evaporation during this stage can be neglected. The evaporation is essential during the next three stages. The next stage after the spreading, which is referred to herein as the first stage, takes place at constant perimeter and ends when θ reaches the static receding contact angle, θ_r. During the next, second stage, the perimeter decreases at constant contact angle θ = θ_r for surfactant concentration above the critical wetting concentration (CWC). The static receding contact angle decreases during the second stage for concentrations below CWC because the concentration increases due to the evaporation. During the final stage both the perimeter and the contact angle decrease. In what follows, we consider only the longest stages I and II. The developed theory predicts universal curves for the contact angle dependency on time during the first stage, and for the droplet perimeter on time during the second stage. A very good agreement between theory and experimental data has been found for the first stage of evaporation, and for the second stage for concentrations above CWC; however, some deviations were found for concentrations below CWC.

The forces acting in colloidal suspensions and affecting their stability and aggregation kinetics are considered. The approximations used for these forces in numerical simulations and the importance of the balanced account for both colloidal forces and hydrodynamic interactions are discussed. As an example the results of direct numerical simulations of kinetics of aggregation either with account for hydrodynamic interaction between particles or without it are compared by varying the parameters of the interaction potential between particles and fraction of solid. Simulations are based on the Langevin equations with pairwise interaction between particles and take into account Brownian, hydrodynamic and colloidal forces. It is confirmed that the neglecting of hydrodynamic interaction results in an accelerated growth of aggregates. The results of numerical simulations of aggregation kinetics are compared with well known analytical solutions.

The recent progress in theoretical and experimental studies of simultaneous spreading and evaporation of liquid droplets on solid substrates is discussed for pure liquids including nanodroplets, nanosuspensions of inorganic particles (nanofluids) and surfactant solutions. Evaporation of both complete wetting and partial wetting liquids into a nonsaturated vapour atmosphere are considered. However, the main attention is paid to the case of partial wetting when the hysteresis of static contact angle takes place. In the case of complete wetting the spreading/evaporation process proceeds in two stages. A theory was suggested for this case and a good agreement with available experimental data was achieved. In the case of partial wetting the spreading/evaporation of a sessile droplet of pure liquid goes through four subsequent stages: (i) the initial stage, spreading, is relatively short (1-2 min) and therefore evaporation can be neglected during this stage; during the initial stage the contact angle reaches the value of advancing contact angle and the radius of the droplet base reaches its maximum value, (ii) the first stage of evaporation is characterised by the constant value of the radius of the droplet base; the value of the contact angle during the first stage decreases from static advancing to static receding contact angle; (iii) during the second stage of evaporation the contact angle remains constant and equal to its receding value, while the radius of the droplet base decreases; and (iv) at the third stage of evaporation both the contact angle and the radius of the droplet base decrease until the drop completely disappears. It has been shown theoretically and confirmed experimentally that during the first and second stages of evaporation the volume of droplet to power 2/3 decreases linearly with time. The universal dependence of the contact angle during the first stage and of the radius of the droplet base during the second stage on the reduced time has been derived theoretically and confirmed experimentally. The theory developed for pure liquids is applicable also to nanofluids, where a good agreement with the available experimental data has been found. However, in the case of evaporation of surfactant solutions the process deviates from the theoretical predictions for pure liquids at concentration below critical wetting concentration and is in agreement with the theoretical predictions at concentrations above it.