Recent advances in the microfabrication technology have made it possible to control surface properties at micro- and nanoscale levels. Functional surfaces drastically change wettability and condensation processes that are essential for controlling of heat transfer. However, the direct observation of condensation on micro- and nanostructure surfaces is difficult, and further understanding of the effects of the microstructure on the phase change is required. In this research, the contact angle of droplets with a wall surface and the initial condensation process were analyzed using a molecular dynamics simulation to investigate the impact of nanoscale structures and their adhesion force on condensation. The results demonstrated the dependence of the contact angle of the droplets and condensation dynamics on the wall structure and attractive force of the wall surface. Condensed water droplets were adsorbed into the nanostructures and formed a water film in case of a hydrophilic surface.

The panel patterns of soccer balls that change with each World Cup have a significant impact on the balls’ aerodynamic and flight characteristics. In this study, the aerodynamic forces of eleven types of soccer ball with different panel patterns were measured in a wind tunnel experiment. We characterized the panel shapes of soccer balls by the length, cross-sectional area, and the panel grooves’ volume. The results confirmed that the drag and drag crisis characteristics are dependent on the groove length and volumes. Flow separation points were visualized by an oil film experiment and particle image velocimetry (PIV) measurement to understand the drag crisis of the soccer balls. The results showed that the panel shape of the ball significantly changes the position of the separation point near the critical region, where the drags crisis occurs. In the critical region, laminar and turbulent flows coexist on the ball. On the other hand, the effect of panel shape on the separation point position is small in subcritical and supercritical states.

The degradation of microplastics in relation to marine pollution has been receiving increasing attention. Because the spherulites that comprise microplastics have a highly ordered lamellar structure, their decomposition is thought to involve a lamellar structure collapse process. However, even in the simplest case of an order–disorder transition between lamellae and melt upon heating, the microscopic details of the transition have yet to be elucidated. In particular, it is unclear whether nucleation occurs at defects in the crystalline portion or at the interface between the crystalline and amorphous portions. To observe the transition in molecular simulations, an approach that distinguishes between the crystalline and amorphous structures that make up the lamella is needed. Local order parameters (LOPs) are an attempt to define the degree of order on a particle-by-particle basis and have demonstrated the ability to precisely render complex order structure transitions during phase transitions. In this study, 274 LOPs were considered to classify the crystalline and amorphous structures of polymers. Supervised machine learning was used to automatically and systematically search for the parameters. The identified optimal LOP does not require macroscopic information such as the overall orientation direction of the lamella layers but can precisely distinguish the crystalline and amorphous portions of the lamella layers using only a small amount of neighboring particle information.

A knuckle shot, resulting from non-spinning kicking, is an essential technique in soccer. The irregular flight path of the knuckle shot is caused by the aerodynamic force from the three-dimensional twin vortices generated in the wake behind the ball. However, the detailed behavior of the twin vortices and relation between the jet flow and the acting forces on the balls is still not understood. In addition, a more thorough understanding of the effect of ball panels on the formation of twin vortices and jet flow is important to develop balls with high controllability. To study the effect of the ball panel shape on the flight path, stereo three-dimensional particle image velocimetry wake flow measurements and synchronized force measurements were performed on various soccer balls. It was confirmed that the aerodynamic force on the ball is produced by the jet flow generated by the vortices in the wake flow. The directions of the force followed the changes of the jet flow, and the magnitude of the force was strongly associated with the flow rate of the jet. Moreover, the shape of the ball panels, especially the groove volume, determines the critical Reynolds number and the fluttering of the balls.

A floater serve in volleyball is a technique of serving a non-rotating or low-rotating ball, which is difficult to return because the flight path of the ball changes irregularly. On the other hand, the randomness of the trajectory makes it difficult for the ball to fall on the target. Players are required to serve taking into account the variability of the trajectory. In previous studies using wind tunnels, it was shown that aerodynamic characteristics such as drag force and lateral force applied to the ball vary depending on the type of ball and the orientation of the panel. Therefore, in order to control the flight trajectory, it is necessary to understand the aerodynamic characteristics of each ball. Since the velocity of the ball and the fluid force applied to the ball changes during flight, it is important to measure not only the fluid force at a steady state in the wind tunnel but also the actual flight distance of the ball. In this study, to provide valuable information for precise control of floater serves, we measured the drag force applied to the ball in a wind tunnel and the flight distance of the ball using an ejection machine, and clarified the effects of the type of ball and the panel face. In the drag force measurement, the drag force on three types of balls, V200W, MVA200, and FLISTATEC, was measured in the wind speed range of 4 m/s to 30 m/s. In the ejection measurement, the ball flight distances were measured while changing the orientation of the panel using an ejection machine. Basically, the FLISTATEC, MVA200, and V200W, in that order, were more likely to increase the distance and the variability, but it was shown that the drop point could be adjusted slightly by selecting the panel face. This result was also obtained when a human player actually served the ball, indicating the tactical importance of the player consciously controlling the direction of the panel. The tactical importance of the player’s conscious control of the direction of the panel was demonstrated. We also proposed receiver positions that would be effective based on the characteristics of each ball.