In recent decades, considerable efforts have been devoted to process automation in agriculture. Regarding irrigation systems, this demand has found several difficulties, including the lack of communication networks and the large distances to electricity supply points. With the recent implementation of LPWAN wireless communication networks (SIGFOX, LoraWan, and NBIoT), and the expanding market of electronic controllers based on free software and hardware (i.e., Arduino, Raspberry, ESP, etc.) with low energy requirements, new perspectives have appeared for the automation of agricultural irrigation networks. This paper presents a low-cost solution for automatic cloud-based irrigation. In this paper, it is proposed the design of a node network based on microcontroller ESP32-Lora and Internet connection through SIGFOX network. The results obtained show the stability and robustness of the designed system.

Increasing the efficiency of water supply networks is essential in arid and semi-arid regions to ensure the supply of drinking water to the inhabitants. The cost of renovating these systems is high. However, customized management models can facilitate the maintenance and rehabilitation of hydraulic infrastructures by optimizing the use of resources. The implementation of current Internet of Things (IoT) monitoring systems allows decisions to be based on objective data. In water supply systems, IoT helps to monitor the key elements to improve system efficiency. To implement IoT in a water distribution system requires sensors that are suitable for measuring the main hydraulic variables, a communication system that is adaptable to the water service companies and a friendly system for data analysis and visualization. A smart pressure monitoring and alert system was developed using low-cost hardware and open-source software. An Arduino family microcontroller transfers pressure gauge signals using Sigfox communication, a low-power wide-area network (LPWAN). The IoT ThingSpeak platform is used for data analysis and visualization. Additionally, the system can send alarms via SMS/email in real time using the If This, Then That (IFTTT) web service when anomalous pressure data are detected. The pressure monitoring system was successfully implemented in a real water distribution network in Spain. It was able to detect both breakdowns and leaks in real time.

The control of refrigeration in the food chain is fundamental at all stages, with special emphasis on the retail stage. The implementation of information and communication technologies (IoT, open-source hardware and software, cloud computing, etc.) is representing a revolution in the operational paradigm of food control. This paper presents a low-cost IoT solution, based on free hardware and software, for monitoring the temperature in refrigerated retail cabinets. Specifically, the use of the ESP-8266-Wi-Fi microcontroller with DS18B20 temperature sensors is proposed. The ThingSpeak IoT platform is used to store and process data in the cloud. The solution presented is robust, affordable, and flexible, allowing to extend the scope of supervising other relevant parameters in the operating process (light control, energy efficiency, consumer presence, etc.).

Agrivoltaics is currently presented as a possible effective solution to one of society’s greatest challenges: responding to the increasing demand for energy and food in an efficient and sustainable manner. To this end, agrivoltaics proposes to combine agricultural and renewable energy production on the same land using photovoltaic technology. The performance of this new production model strongly depends on the interaction between the two systems, agricultural and photovoltaic. In that sense, one of the most important aspects to consider are the effects of the shadows of the photovoltaic panels on the crop land. Therefore, further study of crop behavior under agrivoltaic conditions requires exhaustive knowledge of the spatial distribution of solar radiation within the portion of land between collectors and crops. This study presents a valid methodology to estimate this distribution of solar irradiance in agrivoltaic installations as a function of the photovoltaic installation geometry and the levels of diffuse and direct solar irradiance incident on the crop land. As an example, this methodology was applied to simulate the radiative capture potential of possible photovoltaic plants located in Cordoba, Spain by systematically varying the design variables of the photovoltaic plants. Based on the results obtained, a model correlating the agrivoltaic potential of a photovoltaic plant with its design variables is proposed. Likewise, for the “Alcolea 1” photovoltaic plant (Cordoba, Spain), the solar radiation decay profiles were simulated in the lanes between the photovoltaic collectors where the crops would be planted in the event of converting this plant into an agrivoltaic facility. Thus, the methodology proposed represents an interesting way to determine the agrivoltaic potential of existing grid-connected photovoltaic installations that could be converted into agrivoltaic installations, contributing to the implementation of this new agricultural production model that is more sustainable and environmentally committed to the future.

The growing need to improve the environmental and energy sustainability of buildings involves the use of solar radiation incident on their surfaces. However, in cities, this task is complicated due to the constructive geometry that leads to shading between buildings. In this context, this work presents a study of solar access to the façades of buildings in cities. The methodology is based on the determination of the incident annual solar radiation in 121 significant points of each façade considering the twelve representative days of the year. To characterize the influence of the different city typologies on solar access, the urban solar coefficient is proposed. A study of two neighborhoods in Cordoba (Spain) with different urban settings have been analyzed. Specifically, two typologies of neighborhoods have been compared: one with “L-shaped” and “U-shaped blocks” and another with “Grouped blocks”. For both of them, the Urban Solar Coefficient has been calculated, obtaining a higher mean value for the neighborhood with “L-shaped” and “U-shaped blocks” (0.317) than for the one with “Grouped blocks” (0.260). Accordingly, the results show that urban morphology can influence the Urban Solar Coefficient and solar access. Finally, a regression model for each neighborhood has been obtained in order to determine the dependence of the Urban Solar Coefficient on neighborhood geometry factors.