Shingo Ishihara

Dr. Shingo Ishihara

Tohoku University

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 May 2019 in ISIJ International
Verified
Journal Article
Open access
PDF file
SIShingo Ishihara
Shingo Ishihara
JKJunya Kano
Junya Kano
Breakage behavior of irregular shaped particles was analyzed by ADEM (Advanced Distinct Element Method). This paper attempted to determine ADEM parameters to represent breakage behavior of irregular shaped particles. Compression test have been carried out experimentally to obtain information about particle breakage. In the simulation, joint spring coefficient and maximum strain were parameters for reproducing the experimental results. Pumice was chosen as a sample, and the shape was measured by 3D scanner. Obtained 3D data was converted to cluster particle which is agglomerate of primary particles. Simulation results were compared to experimental results from the view point of load-displacement curve and the shape of samples after breakage. In the simulation, the gradient of load in response to displacement obviously increases with an increase in the joint spring coefficient. Compressive strength increases with an increase in the maximum strain. Impact test was carried out to confirm whether the parameters determined by compression test can also be applied to other breakage behavior. In the impact test, a stainless steel ball was free-falling on the cluster particle from 200 or 400 mm in drop height. In experiment, the number of dropping times needed for breakage decrease with increase in falling height. Same tendency could be observed in the simulation. Breakage behavior in impact test could express by ADEM simulation using the simulation parameters obtained from compression test. According to these results, it is suggested that ADEM has a possibility to become a useful tool to analyze particle breakage behavior.

1 December 2022 in Advanced Powder Technology
Verified
Journal Article
Open access
SIShingo Ishihara
Shingo Ishihara
GFGeorge Franks
George Franks
JKJunya Kano
Junya Kano

1 September 2008 in IEICE Transactions on Electronics
Verified
Journal Article
Closed access
MHM. Hariyama
M. Hariyama
SIShingo Ishihara
Shingo Ishihara
MKM. Kameyama
M. Kameyama

10 September 2021 in Advanced Powder Technology
Verified
Journal Article
Closed access
TWTomoya Wada
Tomoya Wada
TUTakafumi Uematsu
Takafumi Uematsu
HSHiroyuki Shiomi
Hiroyuki Shiomi
KOKazutomo Osaki
Kazutomo Osaki
SIShingo Ishihara
Shingo Ishihara
JKJunya Kano
Junya Kano

14 February 2020 in Processes
Verified
Journal Article
Open access
PDF file
SNShungo Natsui
Shungo Natsui
KTKazui Tonya
Kazui Tonya
HNHiroshi Nogami
Hiroshi Nogami
TKTatsuya Kikuchi
Tatsuya Kikuchi
RSRyosuke, O. Suzuki
Ryosuke, O. Suzuki
SUShigeru Ueda
Shigeru Ueda
In the bottom region of blast furnaces during the ironmaking process, the liquid iron and molten slag drip into the coke bed by the action of gravity. In this study, a practical multi-interfacial smoothed particle hydrodynamics (SPH) simulation is carried out to track the complex liquid transient dripping behavior involving two immiscible phases in the coke bed. Numerical simulations were performed for different conditions corresponding to different values of wettability force between molten slag and cokes. The predicted dripping velocity changes and interfacial shape were investigated. The relaxation of the surface force of liquid iron plays a significant role in the dripping rate; i.e., the molten slag on the cokes acts as a lubricant against liquid iron flow. If the attractive force between the coke and slag is smaller than the gravitational force, the slag then drops together with the liquid iron. When the attractive force between the coke and slag becomes dominant, the iron-slag interface will be preferentially detached. These results indicate that transient interface morphology is formed by the balance between the momentum of the melt and the force acting on each interface.

1 January 2021 in Advanced Powder Technology
Verified
Journal Article
Open access
KKKizuku Kushimoto
Kizuku Kushimoto
MMMika Moriyama
Mika Moriyama
ASAtsuko Shimosaka
Atsuko Shimosaka
YSYoshiyuki Shirakawa
Yoshiyuki Shirakawa
JHJusuke Hidaka
Jusuke Hidaka
JKJunya Kano
Junya Kano