Ayman Bayomy

Ayman Bayomy


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 March 2022 in Applied Thermal Engineering
Verified
Journal Article
Closed access
MMMagdy Mousa
Magdy Mousa
ABAyman Bayomy
Ayman Bayomy
Ziad SaghirZiad Saghir
Ziad Saghir

9 September 2020 in Energies
Verified
Journal Article
Open access
PDF file
MMMagdy Mousa
Magdy Mousa
ABAyman Bayomy
Ayman Bayomy
Ziad SaghirZiad Saghir
Ziad Saghir
Phase change materials (PCM) utilization in energy storage systems represents a point of interest and attraction for the researchers to reduce greenhouse gas emissions. PCM have been used widely on the interior or exterior walls of the building application to optimize the energy consumption during heating and cooling periods. Meanwhile, ground source heat pump (GSHP) gained its popularity because of the high coefficient of performance (COP) and low running cost of the system. However, GSHP system requires a stand-by heat pump during peak loads. This study will present a new concept of energy piles that used PCM in the form of enclosed tube containers. A lab-scaled foundation pile was developed to examine the performance of the present energy pile, where three layers of insulation replaced the underground soil to focus on the effect of PCM. The investigation was conducted experimentally and numerically on two identical piles with and without PCM. Moreover, a flow rate parametric study was conducted to study the effect of the working fluid flow rate on the amount of energy stored and released at each model. Finally, a comprehensive Computational fluid dynamic (CFD) model was developed and compared with the experimental results. There was a good agreement between the experimental measurements and the numerical predictions. The results revealed that the presence of PCM inside the piles increased not only the charging and discharging capacity but also the storage efficiency of the piles. It was found that PCM enhances the thermal response of the concrete during cooling and heating processes. Although increasing the flow rate increased charging and discharging capacity, the percentage of energy stored/released was insignificant compared to the flow rate increasing percentage.

1 November 2020 in International Journal of Thermofluids
Verified
Journal Article
Open access
ZAZ. Alhajaj
Z. Alhajaj
ABAyman Bayomy
Ayman Bayomy
MSM.Z. Saghir
M.Z. Saghir

20 February 2020 in International Journal of Energy Research
Verified
Journal Article
Closed access
PDF file
ABAyman Bayomy
Ayman Bayomy
Ziad SaghirZiad Saghir
Ziad Saghir

19 September 2019 in Journal of Thermal Science and Engineering Applications
Verified
Journal Article
Closed access
PDF file
Ziad SaghirZiad Saghir
Ziad Saghir
CWChristopher Welsford
Christopher Welsford
PTPirassanth Thanapathy
Pirassanth Thanapathy
ABAyman Bayomy
Ayman Bayomy
CDCayley Delisle
Cayley Delisle
The rapid rate of improvement in electronic devices has led to an increased demand for effective cooling techniques. The purpose of this study is to investigate the heat transfer characteristics of an aluminum metallic foam for use with an Intel core i7 processor. The metal foams used have a porosity of 0.91 and different permeabilities ranging from 10 pores per inch (PPI) to 40 PPI. The flow rate at the entrance of the porous cavity varied from 0.22 USGPM to 0.1 USGPM. The fluid consists of water with aluminum nanoparticles having a concentration from 0.1% to 0.5%. The heat fluxes applied at the bottom of the porous test cell vary from 13.25 W/cm2 to 8.34 W/cm2. It has been observed that nanofluid and forced convection improves heat extraction. These observations lead to the conclusion that heat enhancement is possible with nanofluid and it is enhanced further in the presence of a high flow rate. However, it was detected experimentally, verified numerically, and agreed upon by different researchers that higher heat extraction is found for a nanofluid concentration of 0.2%. This observation is independent of the porous permeability or applied heat flux. It has also been shown that heat enhancement in the presence of nanofluid is evident, when experimental results were compared to water.

2 April 2021 in International Journal of Energy Research
Verified
Journal Article
Closed access
PDF file
ABAyman Bayomy
Ayman Bayomy
JWJun Wang
Jun Wang
Seth DworkinSeth Dworkin
Seth Dworkin