wenjun Gong

Dr. wenjun Gong


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 July 2015 in Science China Technological Sciences
Verified
Journal Article
Open access
PDF file
ZCZuYu Chen
ZuYu Chen
WGwenjun Gong
wenjun Gong
GMGuoWei Ma
GuoWei Ma
JWJie Wang
Jie Wang
LHLei He
Lei He
JXJianYing Xing
JianYing Xing
This paper presents series studies on the toppling mechanism by centrifuge tests and numerical simulations. Two different discrete element methods, i.e., the continuum-based discrete element method (CDEM) and the discontinuous deformation analysis (DDA), are adopted. The modeling results show that both the methods can accurately capture the failure modes of the centrifuge tests, including three distinct zones and two failure surfaces. Comparisons are made between the physical test and numerical simulation results. The critical inclination angle of the tilting table where the slope models are fixed on can be moderately predicted by the two methods, with different degrees of precision. The error between the test results and the simulated results is within 1% for the slope models without rock-bridges by both CDEM and DDA. However, it is amplified for the staggered-joint models that simulate the rock-bridges. With DDA, the average error is about 5%, and the maximum error is up to 17%. While with CDEM, the errors for the aligned-joint models are ranged from 1% to 6%, and it is from 10% to 29% for the staggered-joint models. The two numerical methods show the capability in simulating toppling failure of blocky rock mass with and without rock-bridges. The model with rock-bridges which provides a certain bending resistance is more stable than the one without any rock-bridge. In addition, the two failure surfaces were observed, which is different from the common understanding that only one failure surface appears.

14 February 2017 in International Journal for Numerical and Analytical Methods in Geomechanics
Verified
Journal Article
Closed access
PDF file
WGwenjun Gong
wenjun Gong
YWYunsheng Wang
Yunsheng Wang
Youjun NingYoujun Ning
Youjun Ning
YLYonghong Luo
Yonghong Luo
YWYujie Wang
Yujie Wang

1 August 2022 in KSCE Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
WGwenjun Gong
wenjun Gong
ZTZhi Gang Tao
Zhi Gang Tao
MHMan Chao He
Man Chao He
HHHui Jun Hou
Hui Jun Hou
As a typical and complex failure type of rock slopes, flexural toppling failure has increasingly received attention, mainly focused on its failure mechanism and introducing a proper numerical method to reproduce the failure phenomena. However, there are few studies related to the supporting mechanism against flexural toppling failure. This study attempted to make a preliminary analysis on the research gap. For this purpose, an anti-dip layered rock slope supported with anchor cables that failed owning to flexural toppling was taken as an example, and the numerical method discontinuous deformation analysis (DDA) was taken as the major analytical tool. Firstly, the rationality of DDA was verified by correctly simulating the failure state of the anti-layered rock slope and the underlying failure mechanism was studied. The results indicated that the lack of the support from slope toe is the crucial factor inducing the flexural toppling failure, which posed a great obstacle to the further excavation of the open-pit mine. Secondly, by introducing the anchor cable support to the slope toe in the DDA model, the interaction mechanism between the anchor cables and the rock slope was investigated. the results indicated that the supporting system of the ordinary anchor cables is very sensitive to the inhomogeneous flexural toppling deformation. The tension values of the anchor cables are very inhomogeneous, and once some of anchor cables beyond their tension limit, the anchor cables failed, which will greatly threaten the safety of the adjacent anchor cables and even the stability of the whole slope. Meanwhile, a novel anchor cable called constant-resistance-large-deformation (CRLD) anchor cable was introduced for a comparative study using DDA. just replacing the anchor cables of the original slope with the CRLD anchor cables, the slope can reach stable state eventually even without the slope toe being enhanced. In addition, the CRLD anchor cables were able to support the slope well against the inhomogeneous deformation, because they can provide high constant resistances and withstand large deformations. This study can provide a deeper insight into the support mechanism for the snit-layered rock slope against flexural toppling failure and introduce a novel supporting method for such slopes.

2 October 2020 in KSCE Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
WGwenjun Gong
wenjun Gong
YWYunsheng Wang
Yunsheng Wang
YWYujie Wang
Yujie Wang
YLYonghong Luo
Yonghong Luo
For the prevention and mitigation of hazards, it is crucial to quantitatively analyze the seismic response of rock slopes. However, only a few studies have quantitatively analyzed the seismic response of rock slopes; these studies have considered topographic effects only and have neglected geological site effects, such as impedance contrasts and fractures, which are important factors affecting the seismic response of rock slopes, as revealed by multiple recent phenomena. Therefore, this study primarily aims to investigate the possibility of employing a numerical model for quantitatively analyzing the seismic response of rock slopes by considering the geological site effects. Herein, a discrete element method, i.e., discontinuous deformation analysis (DDA), was employed for the dynamic analyses, and a well-monitored rock slope, Mount Dong, was selected as the case study. In the proposed DDA model, horizontal and vertical ground motions were applied simultaneously. The different weathering degrees of the Mount Dong rock layers were considered to reflect the impedance contrasts, and the penalty value at the fractures was altered according to the stiffness for reflecting the fracture effects. Furthermore, a set of optimal boundary settings, especially for DDA, were applied to handle seismic dynamic problems. Results show that DDA can quantitatively reflect the seismic response of Mount Dong along a single direction, such as the horizontal direction, which is sufficient to satisfy engineering requirements. The peak ground acceleration amplification analyses indicate that: 1) a strong impedance contrast is more important than topographic effects for the seismic response of Mount Dong; and 2) in addition to the impedance of rock layers, widely spread fractures also play an important role in contributing to the seismic response anisotropy of rock slopes. Finally, spectral amplification analyses reveal that the responses of the inner and surface portion of Mount Dong are significant in a low- and high-frequency range, respectively.

20 March 2019 in KSCE Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
WGwenjun Gong
wenjun Gong
JHJing Hu
Jing Hu
ZTZhigang Tao
Zhigang Tao
This paper is mainly aimed to present an improved DDA (discontinuous deformation analysis) that can deal well with both shear and tensile failure problems. Firstly, the shear mechanism of DDA is detailed investigated. The results show that when handling the frictional interface, the critical shear resistance can be accurately determined only if the penalty value is carefully selected, however, when handling the cohesive interface, the critical shear resistance is significantly underestimated. The inaccurate prediction is due to the inconsistent distribution of normal force and shear force between the two vertex-to-edge contacts in one edge-to-edge contact. Here an edge-to-edge treatment is introduced into DDA. Secondly, to moderately reflect the tensile failure process of rock masses, a two-phase constitutive model is introduced into the DDA with edge-to-edge treatment, and the improved DDA is obtained. Finally, the improved DDA is used to simulate the failure process of gypsum centrifuge model. The results show the improved DDA can deal well with rock failure problems by shear or tension failure.