Electrowetting display (EWD) has promising prospects in the electronic paper industry due to it having superior characteristics, such as the ability to provide a comfortable reading experience and quick response. However, in real applications, there are also problems related to dielectric deterioration, excess power consumption, optical instability and narrow color gamut etc. This paper reviewed the existing challenges and recent progress made in terms of improving the optical performance and reliability of EWD. First, the principle of electrowetting applied in small and confined configurations is introduced and the cause of the failure of the dielectric layer is analyzed. Then, the function of the pixel structures is described to avoid display defects. Next, electric signal modulations are compared in terms of achieving good image quality and optical stability. Lastly, the methods are presented for color panel realization. It was concluded that multi-layer dielectrics, three-dimensional pixel structures, proper electric frequency-and-amplitude modulation and an RGB color panel are expected to resolve the current limitations and contribute to designing advanced reflective displays.

Electrowetting has drawn significant interest because of the potential applications of displays, lab-on-a-chip microfluidic devices, electro-optical switches, and so forth. However, electrowetting display (EWD) is monostable, which needs extra continuous voltage supply to keep contracting the oil. This paper is concerned with the simulation of two-phase liquid flow in three-dimensional EWD pixels with two electrodes (E1 and E2) demonstrating bistability, where power is only needed to move the oil droplet between two stable states. The effects of E1 geometry, E2 geometry, and E2 pulse characteristics on the dynamics of the oil droplet motion have been analyzed. Also, predictions of the transient states in four stages of the reversible bistable operation process have been carried out by employing the finite element method, in qualitative agreement with our experimental results of the monostable EWD and the existing literature. We seek to shed more light on the fundamental two-phase liquid flow in three-dimensional pixels exhibiting bistability for low power EWD and guide optimizing the electrodes to the perfect patterns with the aid of rigorous modeling.

Colorful electrowetting displays (EWD) present many challenges, such as scalability and electro-optical performance improvement (e.g., brightness, color gamut, and contrast ratio). The first full investigation of scalable fabrication and testing processes for multi-color segmented EWD with potentially unprecedented electro-optical performance is proposed. A three-layer architecture is employed to achieve colorful EWD, where the key components are three primary color layers (cyan, magenta, and yellow), switched independently. Unlike previous reports referred to herein, which used the same fabrication and testing processes for each layer, this architecture facilitates a uniform performance, improves yield, and simplifies the process for colorful EWD. With an aperture ratio greater than 80%, National Television Standards Committee (NTSC) color gamut area greater than 63%, switching speed lower than 12 ms, and DC driving voltage below 22V, the testing results of colorful EWD are proven successfully by using our proposed processes. The processes investigated in this paper have greatly improved efficiency, suitable for a high-volume of full-color EWD.

We designed, fabricated and measured full-color, reflective electrowetting displays (EWDs). The display system is composed of three-layer cyan, magenta and yellow EWD elements fabricated with standard photolithographic techniques. The EWDs were driven successfully by the proposed control system and the measurement results show that the electro-optical performance was improved. The aperture ratio of the EWD element can be tuned from 0 to ∼80% as the applied voltage is changed from 0 to 30 V. The response time and the color gamut were measured to be ∼18 ms and ∼58% NTSC, respectively. This paper makes it possible for large numbers of reflective full-color EWDs to be fabricated directly, with advantages of saving power significantly by 85% and no eye irritation compared with LED displays.

Bistable electrowetting displays (BEWDs) have become a competitive technical solution for low-power and static display fields due to their unique zero-power-consumption holding characteristics. However, traditional BEWD pixels face problems such as high driving voltage, complex processes, high cost, open structures, and difficulty in high-resolution array fabrication. Aiming at these bottlenecks, this paper proposes a closed stereoscopic bistable EWD pixel structure driven by planar and non-planar electrodes, and completes the design, fabrication, and performance verification of the device. The fabrication process proposed in this paper combines photolithography and inkjet printing, featuring simple process, low cost, closed pixels, and low driving voltage, which solves the key problems of traditional processes. The research results provide a feasible process route and experimental basis for the development of low-power bistable electrowetting display devices.