A comparative study of the microstructure, hardness, and tribological properties of two different AISI H13 tool steels—classified as the bulk with no heat treatment steel or the 3D-printed steel—was undertaken. Both samples were subjected to ultrasonic nanocrystalline surface modification (UNSM) to further enhance their mechanical properties and improve their tribological behavior. The objective of this study was to compare the mechanical properties and tribological behavior of these tool steels since steel can exhibit a wide variety of mechanical properties depending on different manufacturing processes. The surface hardness of the samples was measured using a micro-Vickers hardness tester. The hardness of the 3D-printed AISI H13 tool steel was found to be much higher than that of the bulk one. The surface morphology of the samples was characterized by electron backscattered diffraction (EBSD) in order to analyze the grain size and number of fractions with respect to the misorientation angle. The results revealed that the grain size of the 3D-printed AISI H13 tool steel was less than 0.5 μm, whereas that of the bulk tool steel was greater than 4 μm. The number of fractions of the bulk tool steel was about 0.5 μm at a low misorientation angle, and it decreased gradually with increasing misorientation angle. The low-angle grain boundary (LAGB) and high-angle grain boundary (HAGB) of the bulk sample were about 21% and 79%, respectively, and those of the 3D-printed sample were about 8% and 92%, respectively. Moreover, the friction and wear behavior of the UNSM-treated AISI H13 tool steel specimen was better than those of the untreated one. This study demonstrated the capability of 3D-printed AISI H13 tool steel to exhibit excellent mechanical and tribological properties for industrial applications.

The current research reports the improvement in surface integrity and tribological characteristics of steel prepared using a powder metallurgy (PM) by ultrasonic nanocrystal surface modification (UNSM) at 25 and 300 °C. The surface integrity and tribological properties of three samples, namely, as-PM, UNSM-25 and UNSM-300 were investigated. The average surface roughness (R_a) of the as-PM, UNSM-25 and UNSM-300 samples was measured using a non-contact 3D scanner, where it was found to be 3.21, 1.14 and 0.74 µm, respectively. The top surface hardness was also measured in order to investigate the influence of UNSM treatment temperature on the hardness. The results revealed that the as-PM sample with a hardness of 109 HV was increased up to 165 and 237 HV, corresponding to a 32.1% and 57.2% after both the UNSM treatment at 25 and 300 °C, respectively. XRD analysis was also performed to confirm if any changes in chemistry and crystal size were took place after the UNSM treatment at 25 and 300 °C. In addition, dry tribological properties of the samples were investigated. The friction coefficient of the as-PM sample was 0.284, which was reduced up to 0.225 and 0.068 after UNSM treatment at 25 and 300 °C, respectively. The wear resistance was also enhanced by 33.2 and 52.9% after UNSM treatment at both 25 and 300 °C. Improvements in surface roughness, hardness and tribological properties was attributed to the elimination of big and deep porosities after UNSM treatment. Wear track of the samples and wear scar of the counter surface balls were investigated by SEM to reach a comprehensive discussion on wear mechanisms. Overall, it was confirmed that UNSM treatment at 25 and 300 °C had a beneficial effect on the surface integrity and tribological characteristics of sintered steel by the PM that is used in a shock absorber for a car engine.

Glass with strong durability and transparency has been in the spotlight in various fields, including displays. Elastic and shear moduli and Poisson’s ratio are important properties of glasses. The purpose of this study is to evaluate the change in mechanical properties, such as the dynamic elastic modulus and Poisson’s ratio, with respect to the chemical strengthening time of glass for display applications, as measured by static and dynamic methods. The basic measurement principle of the dynamic method is to measure acoustic speed or resonant frequency using an ultrasonic generator. The mechanical properties of both non-strengthened and chemically strengthened glasses were investigated. It was found that the strength of the chemically strengthened glass decreased when chemical strengthening time increased. Chemical strengthening increased the bending strength and decreased the elastic modulus due to the introduction of compressive residual stress at the surface.

Welding defects are common during the production of large welded structures. However, few studies have explored methods of compensating for clear welding defects without resorting to re-welding. Here, an ultrasonic peening method to compensate for the deteriorated mechanical properties of overlap weld defects without repair welding was studied. We experimentally investigated changes in the mechanical properties of defective welds before and after ultrasonic peening. The weld specimen with an overlap defect contained a large cavity-type defect inside the weld bead, which significantly reduced the fatigue life. When the surface of the defective test piece was peened, the fatigue life of the weld plate was restored, resulting in an equivalent or higher number of cycles to failure, compared to a specimen with a normal weld. The recovery of mechanical properties was attributed to the effect of surface work hardening by ultrasonic peening and the change in stress distribution. Thus, ultrasonic peening could compensate for the deterioration of mechanical properties such as tensile strength, fatigue life, and elongation due to overlap defects, without resorting to repair welding.

Introduction The time criteria used in many studies of postherpetic neuralgia (PHN) are arbitrary and do not have supporting evidence. Therefore, this study sought to determine the definite time criterion for PHN by analyzing the skin temperature to estimate the time point when zoster-induced skin inflammatory reaction ends. Methods Infrared thermography was used to measure the difference in skin temperature between the affected and unaffected areas (ΔTemp) in the craniocervical and thoracic regions of patients with herpes zoster (HZ). Because the ΔTemp changes from a positive value to zero when the skin is no longer inflamed, a ΔTemp ≤ 0 was defined as the end of skin inflammation, and this time point was considered the starting point for PHN. This cutoff time point was estimated using receiver operating characteristic (ROC) curve analysis. Results A total of 503 patients were included in this study. The ROC curve analysis showed that the time point when the ΔTemp was ≤ 0 occurred at 12 weeks after HZ onset (95% confidence interval 11–15 weeks, area under the ROC curve 0.901). Using this time point as the time criterion of PHN, the sensitivity, specificity, and classification accuracy were 0.807, 0.905, and 0.871, respectively. Conclusions The transition of skin temperature from warm to cold occurs 12 weeks after HZ onset, which implies the end of local inflammation. Therefore, PHN associated with pathophysiologic change may be defined as 12 weeks after the skin rash. This finding provides a theoretical basis for the timing definition of PHN.

The purpose of this study is to investigate the fractural behavior of lead (Pb)-free material containing bismuth (Bi) that was developed to replace the Pb included in sintered copper (Cu)-based alloy for plain bearings. Mechanical properties and microstructure of two different sintered Cu-based alloys (CuSn10Pb10 and CuSn10Bi7) were compared and analyzed. Under tensile load, a CuSn10Pb10 layer is decomposed into powder and changed to form pores leading to an expansion. Therefore, even after tensile elongation, the matrix itself did not stretch, with no work hardening. However, in the case of CuSn10Bi7, a Bi kept its original shape, resulting in it being the same length as the steel plate, where the hardness and strength increased due to the effect of work hardening. These results suggested that the performance of the alloys was different under a high tensile load, where plain bearings usually undergo tensile deformation.