Recent studies using satellite data have shown a growing interest in detecting and anticipating landslide failures. However, their value for an actual landslide prediction has shown variable results. Therefore, the use of satellite images for that purpose still requires additional attention. Here, we study the landslide of the Tunnel du Chambon in the French Alps that ruptured in July 2015, generating major impacts on economic activity and infrastructures. To evaluate the contribution of very high-resolution optical satellite images to characterize and potentially anticipate the landslide failure, we conduct here a retro analysis of its evolution. Two time periods are analyzed: September 2012 to September 2014, and May to July 2015. We combine Pléiades optical images analysis and geodetic measurements from in situ topographic monitoring. Satellite images were correlated to detect pre-failure motions, showing 1.4-m of displacement between September 2012 and September 2014. In situ geodetic measures were used to analyze motions during the main activity of the landslide in June and July 2015. Topographic measurements highlight different areas of deformations and two periods of strong activity, related to the last stage of the tertiary creep and to anthropic massive purges of unstable masses. The law of acceleration toward the rupture observed in June and July 2015 over the topographic targets also fits well the satellite observation between 2012 and 2014, showing that the landslide probably already entered into tertiary creep 2.5 years before its failure.
Passive sensors such as multi-spectral (e.g., Single Lens Reflex, SLR) cameras are increasingly being used for geohazards monitoring (landslides, cliffs affected by rock falls, ice glaciers, and volcano flanks) because of their low cost compared to expensive terrestrial laser scanner (TLS) or radar imaging (GB-InSAR) systems. Indeed, due to the large consumer market, sensor resolution and quality (e.g., gain, dynamic range, and geometry) are increasing rapidly. For gravitational processes, such as landslides, recent research has focused on the development and implementation of image correlation techniques to estimate the spatial shift between at least a pair of images by maximizing a cross-correlation function. A generic and fully automated pipeline is proposed for the processing of long image time series acquired for several site configurations. The system associates modules for 1) the selection of the image sequences, 2) the registration of the image stacks and the correction of the camera movements, and 3) the calculation of the terrain motion using change detection approaches. The system is based on the open-source photogrammetric library MicMac and tailored for the processing of monoscopic images. A sensitivity analysis is conducted to design and test the image processing for two use cases respectively the Chambon landslide (Isère, France) characterized by slow motion (< 10 cm.day−1), and the Pas de l’Ours landslide (Hautes-Alpes, France) characterized by moderate motion (> 50 cm.day−1). Four categories of parameters are tested: the image modality, the image matching parameters, the size of the stable area used in the co-registration stage, and the strategy used to combine the images in the time series. The application of the pipeline on the two use cases provides information about the kinematics and the spatial behavior of the landslides.
The analysis of surface displacement and velocity fields from time series of terrestrial optical images is a useful tool for monitoring gravitational instabilities. It allows to define the state of instability of the slope, its evolution in time, its spatial coverage and to identify if the movement is progressing. Other types of information can also be extracted from landslide surface velocity fields such as the tangential and normal deformation or the strain fields that highlight areas of compression/extension (Travelletti et al., 2014) that can even allow to assess the mechanical properties of the moving mass (Baum et al., 1998). However, applying such advanced approaches necessitates to be able to compute the 3D displacements and deconvolute the normal and tangential displacements.Landslide ground motion can be measured by various geodetic techniques either in-situ and point-based, or remote and giving access to spatially distributed information. In this study, we privileged a low-cost remote sensing method based on the use of a Single Lens Reflex (SLR) cameras. We acquired data at high frequency (i.e., time-lapse photography) from two fixed cameras at the Montgombert landslide.The velocity fields were extracted from a time series of 13 images by applying the TSM (Tracing Surface Motion; Desrues et al. 2019) code. To detect tangential and normal displacements, we developed a methodology to construct the 3D displacements directly from the correlation results from the pairwise combination of the two monoscopic velocity fields, and further conducted a deformation analysis.To estimate the thickness of the moving mass from the 3D displacements derived from the stereoscopic optical images, we propose a methodology based on the law of mass conservation (i.e., displacement incompressible) by invoking the rheology of the material involved (Booth et al., 2013). In order to take into account, in this model, a more complex slip geometry, we introduced a disbonding parameter that marks the presence of a dislocation area at the top limit of the moving mass which traduces a non-zero velocity at the sliding surface.We present the methodology of reconstruction of the 3D displacements with a stereoscopic approach and of estimation of the landslide thickness by applying them to the Montgombert use case (Savoie, French Alps). The calculated displacement fields are consistent with in-situ data and the estimated depths, suggesting a shallow sliding, are consistent with geotechnical information.