The importance of supplying drinking water with a balanced mineral composition, including a minimal concentration of Mg(II) ions, has been recently acknowledged by many publications, as well as in official WHO guidelines. The issue is relevant to naturally occurring soft waters and lately to the rapidly increasing volume of supplied desalinated water. This paper presents an enhancement of a recently developed nanofiltration-based method for the selective separation of soluble Mg(II) species from seawater. The generated rich-Mg(II) brine is demonstrated to be suitable for supplementing soft waters with magnesium ions. The brine, generated using a commercial membrane (DS-5 DL, Osmonics) at various operational conditions is characterized by high Mg(II) concentrations (~8.5 g/L) and low Cl:Mg and Na:Mg molar concentration ratios (1.6 and 0.6, respectively, at 28-bar operation). A food-grade antiscalant is dosed to the feed seawater to prevent scaling; however, since the Mg(II) concentration in the brine is high, for attaining 10 mg Mg/L of desalinated water, the dilution ratio with the desalinated water is ~1:850, resulting in maximal additional concentrations of 0.024 antiscalant, 34.9 Cl(−I), 12.9 Na(I), 0.05 Sr(II) and 0.003 B (all concentrations in mg/L). The overall cost of 1 kg of Mg(II) separated by the presented process amounts to between $0.05 and $0.07, i.e., much cheaper than the estimated costs of alternative processes for Mg(II) addition to desalinated water.
Deliberate struvite (MgNH4PO4) precipitation from wastewater streams has been the topic of extensive research in the last two decades and is expected to gather worldwide momentum in the near future as a P-reuse technique. A wide range of operational alternatives has been reported for struvite precipitation, including the application of various Mg(II) sources, two pH elevation techniques and several Mg:P ratios and pH values. The choice of each operational parameter within the struvite precipitation process affects process efficiency, the overall cost and also the choice of other operational parameters. Thus, a comprehensive simulation program that takes all these parameters into account is essential for process design. This paper introduces a systematic decision-supporting tool which accepts a wide range of possible operational parameters, including unconventional Mg(II) sources (i.e. seawater and seawater nanofiltration brines). The study is supplied with a free-of-charge computerized tool (http://tx.technion.ac.il/~agrengn/agr/Struvite_Program.zip) which links two computer platforms (Python and PHREEQC) for executing thermodynamic calculations according to predefined kinetic considerations. The model can be (inter alia) used for optimizing the struvite-fluidized bed reactor process operation with respect to P removal efficiency, struvite purity and economic feasibility of the chosen alternative. The paper describes the algorithm and its underlying assumptions, and shows results (i.e. effluent water quality, cost breakdown and P removal efficiency) of several case studies consisting of typical wastewaters treated at various operational conditions.
1 September 2016 in Desalination and Water Treatment
Magnesium (Mg2+) appears at high concentration in seawater and seawater-reverse-osmosis brines. In contrast, desalinated water is almost completely depleted of Mg2+, a mineral perceived essential for human health and agricultural irrigation. The paper introduces a cost-effective method to enrich desalinated water with an almost pure Mg(II) solution, originating from seawater. The method uses seawater nanofiltration (or nanofiltration of seawater-reverse-osmosis brine) to produce brine characterized by high Mg2+ concentration, accompanied by relatively low B, Cl−, and Na+ concentrations. Subsequently, Mg(II) is separated from the produced nanofiltration brine by precipitating Mg(OH)2(s) and adsorbing it onto the surface of micro-magnetite particles. Finally, the solid slurry (Fe3O4 + Mg(OH)2) is magnetically separated from the brine and the Mg(OH)2(s) is re-dissolved into the desalinated water in a separate reactor. Application of the method results in a relatively pure Mg(II) addition to the desalinated water product. For example, for Mg(II) addition of 10 mg/L (as recommended by the World Health Organization), the following negligible concentrations of unwanted species are added to the water (in mg/L units): Na+: 0.04, Cl−: 0.18, Ca2+: 0.05, and B: 0.0094. The cost of adding 10 mg Mg/L was estimated at 0.76 cent$/m3 of desalinated water, i.e. competitive with previously suggested processes.
The recent supply of large volumes of seawater desalinated water in Israel prompted both the development of new water quality standards and the development of a novel post treatment process, designed to comply with the new standards at a cost effective price. The new process is designed to supply water with alkalinity, Ca2 + and calcium carbonate precipitation potential values as required in the new criteria, along with the addition of a threshold Mg2 + concentration recently recommended by the WHO. The current paper describes the process in general, and focuses in particular on attaining these criteria while maintaining a low total hardness concentration (120 mg/L as CaCO3). The process is based on dissolving calcite using H2SO4 and replacing the excess calcium ions generated in this process by Mg2 + ions (using a specific cation exchange resin—Amberlite) and by Na+ (using a second cation exchange resin—chabazite, from the zeolite group). Once exhausted the resins are re-loaded with Mg2 + and Na+ by the brine generated in the RO process, thus no unwanted brines are generated. A case study is presented for which operational costs were approximated at 0.034 $US/m3 product water.