The paper discusses the concept, design and final results from the ‘Ultra Boost for Economy’ collaborative project, which was part-funded by the Technology Strategy Board, the UK's innovation agency. The project comprised industry- and academia-wide expertise to demonstrate that it is possible to reduce engine capacity by 60% and still achieve the torque curve of a modern, large-capacity naturally-aspirated engine, while encompassing the attributes necessary to employ such a concept in premium vehicles. In addition to achieving the torque curve of the Jaguar Land Rover naturally-aspirated 5.0 litre V8 engine (which included generating 25 bar BMEP at 1000 rpm), the main project target was to show that such a downsized engine could, in itself, provide a major proportion of a route towards a 35% reduction in vehicle tailpipe CO₂ on the New European Drive Cycle, together with some vehicle-based modifications and the assumption of stop-start technology being used instead of hybridization. In order to do this vehicle modelling was employed to set part-load operating points representative of a target vehicle and to provide weighting factors for those points. The engine was sized by using the fuel consumption improvement targets and a series of specification steps designed to ensure that the required full-load performance and driveability could be achieved. The engine was designed in parallel with 1-D modelling which helped to combine the various technology packages of the project, including the specification of an advanced charging system and the provision of the necessary variability in the valvetrain system. An advanced intake port was designed in order to ensure the necessary flow rate and the charge motion to provide fuel mixing and help suppress knock, and was subjected to a full transient CFD analysis. A new engine management system was provided which necessarily had to be capable of controlling many functions, including a supercharger engagement clutch and full bypass system, direct injection system, port-fuel injection system, separately-switchable cam profiles for the intake and exhaust valves and wide-range fast-acting camshaft phasing devices. Testing of the engine was split into two phases. The first usied a test bed Combustion Air Handling Unit to enable development of the combustion system without the complication of a new charging system being fitted to the engine. To set boundary conditions during this part of the programme, heavy reliance was placed on the 1-D simulation. The second phase tested the full engine. The ramifications of realizing the engine design from a V8 basis in terms of residual friction versus the fuel consumption results achieved are also discussed. The final improvement in vehicle fuel economy is demonstrated using a proprietary fuel consumption code, and is presented for the New European Drive Cycle, the FTP-75 cycle and a 120 km/h (75 mph) cruise condition.

This paper investigates components of mechanical loss together with heat transfer effects in an axial-flux permanent-magnet motor. The mechanical loss components generated within electrical machines are well known; however, their prediction or derivation has not been widely reported in the literature. These, together with the electromagnetic loss sources and heat transfer effects, are crucial and must be accounted for when considering high-power-density, high-speed, and/or compact machine designs. This research is focused on separating the mechanical loss components to gain a more in-depth understanding of the effects and their importance. Both experimental and theoretical techniques have been employed in the analysis of a machine demonstrator. In particular, hardware tests with dummy rotors have been performed to measure the bearing and windage/drag loss components. These have been supplemented with computational fluid dynamics analysis to theoretically evaluate the aerodynamic effects occurring within the mechanical air gap accounting for loss and heat transfer. It has been identified that the analyzed hardware demonstrator suffered bearing loss significantly higher than that suggested by the bearing manufacturer. This has been attributed to design of the mechanical assembly accommodating bearings, which resulted in inappropriate bearing preload. The excessive bearing loss had a significant detrimental effect on the machine thermal behavior. In contrast, the aerodynamic effects have been found to have less pronounced effects here, due to fully enclosed and naturally cooled machine construction.

Modern downsized internal combustion engines benefit from high-efficiency turbocharging systems for increasing their volumetric efficiency. However, despite the efficiency increase, turbochargers often lack fast transient response due to the nature of the energy exchange with the engine, which deteriorates the vehicle’s drivability. An electrically-assisted turbocharger can be used for improving the transient response without any parasitic losses to the engine while providing energy recovery for increasing overall system efficiency. The present study provides a detailed numerical investigation on the potential of e-turbocharging to control load and if possible replace the wastegate valve. A parametric study of the optimum compressor/turbine sizing and wastegate area was performed for maximum torque, fast response time and energy regeneration across the real driving conditions speed/load area of the engine. The results showed that the implementation of a motor-generator could contribute to reducing the response time of the engine by up to 90% while improving its thermal efficiency and generating up to 6.6 kWh of energy. Suppressing the wastegate can only be achieved when a larger turbine is implemented, which as a result deteriorates the engine’s response and leads to energy provision demands at low engine speeds.