Changing climates are altering the structural and functional components of forest ecosystems at an unprecedented rate. Simultaneously, we are seeing a diversification of public expectations on the broader sustainable use of forest resources beyond timber production. As a result, the science and art of silviculture needs to adapt to these changing realities. In this piece, we argue that silviculturists are gradually shifting from the application of empirically derived silvicultural scenarios to new sets of approaches, methods and practices, a process that calls for broadening our conception of silviculture as a scientific discipline. We propose a holistic view of silviculture revolving around three key themes: observe, anticipate and adapt. In observe, we present how recent advances in remote sensing now enable silviculturists to observe forest structural, compositional and functional attributes in near-real-time, which in turn facilitates the deployment of efficient, targeted silvicultural measures in practice that are adapted to rapidly changing constraints. In anticipate, we highlight the importance of developing state-of-the-art models designed to take into account the effects of changing environmental conditions on forest growth and dynamics. In adapt, we discuss the need to provide spatially explicit guidance for the implementation of adaptive silvicultural actions that are efficient, cost-effective and socially acceptable. We conclude by presenting key steps towards the development of new tools and practical knowledge that will ensure meeting societal demands in rapidly changing environmental conditions. We classify these actions into three main categories: re-examining existing silvicultural trials to identify key stand attributes associated with the resistance and resilience of forests to multiple stressors, developing technological workflows and infrastructures to allow for continuous forest inventory updating frameworks, and implementing bold, innovative silvicultural trials in consultation with the relevant communities where a range of adaptive silvicultural strategies are tested. In this holistic perspective, silviculture can be defined as the science of observing forest condition and anticipating its development to apply tending and regeneration treatments adapted to a multiplicity of desired outcomes in rapidly changing realities.

There is a growing interest to use acoustic sensors for selection in tree breeding to ensure high wood quality of future plantations. In this study, we assessed acoustic velocity as a selection trait for the improvement of mechanical wood properties in two 15- and 32-year-old white spruce (Picea glauca [Moench.] Voss) genetic tests. Individual heritability of acoustic velocity was moderate and of the same magnitude as heritability of wood density. Considerable genetic gain could be expected for acoustic velocity and a measure combining velocity and wood density. The relationship between acoustic velocity and cellulose microfibril angle (MFA) was strong on the genetic level and selection based on velocity could effectively improve MFA, which is one of the most important determinants of wood mechanical properties. Although low, the positive relationship between acoustic velocity and tree height presents an interesting opportunity for the improvement of both tree growth and wood quality. On the phenotypic level, MFA was more strongly correlated to acoustic velocity in mature trees than in young trees. The addition of easily obtainable traits such as diameter at breast height (DBH), height-to-diameter ratio as well as wood density to velocity determinations could improve models of MFA at the young and the mature age. We conclude that juvenile acoustic velocity is an appropriate trait to select for wood quality in a tree breeding context.

The number of planted trees per hectare influences individual volume growth, which in turn can affect wood properties. The objective of this study was to assess the effect of six different plantation spacings of jack pine (Pinus banksiana Lamb.) 25 years following planting on tree growth, morphology, and wood properties. Stem analyses were performed to calculate annual and cumulative diameter, height, and volume growth. For morphological and wood property measurements several parameters were analyzed: diameter of the largest branch, live crown ratio, wood density, and the moduli of elasticity and rupture on small clear samples. The highest volume growth for individual trees was obtained in the 1111 trees/ha plantation, while the lowest was in the 4444 trees/ha plantation. Wood density and the moduli of elasticity and rupture did not change significantly between the six plantation spacings, but the largest branch diameter was significantly higher in the 1111 trees/ha (3.26 cm mean diameter) compared with the 4444 trees/ha spacing (2.03 cm mean diameter). Based on this study, a wide range of spacing induced little negative effect on the measured wood properties, except for the size of knots. Increasing the initial spacing of jack pine plantations appears to be a good choice if producing large, fast-growing stems is the primary goal, but lumber mechanical and visual properties could be decreased due to the larger branch diameter.

Purpose of Review: Intensive forest management practices are being implemented worldwide to meet future global demand for wood and wood products while facilitating the protection of natural forest ecosystems. A potential decline in wood properties associated with rapid tree growth makes it essential to quantify the potential impact of intensive management on the process of wood formation and, in turn, on its suitability for various end-uses.Recent Findings: Wood produced over short rotations is generally of lower quality because wood properties tend to improve with cambial age (i.e. the number of annual growth rings from the pith). The intensification of silvicultural practices can thus have measurable consequences for the forest products value chain. The use of new planting material from tree improvement programs could offset such effects, but questions arise as to the effects of a changing climate on wood produced from these plantations and the best silvicultural approaches to manage them.Summary: Based on these recent findings, we provide reflections on the need for a modelling framework that uses the effects of cambial age, ring width and position along the stem to summarise the effects of tree growth scenarios on wood properties. We then present challenges related to our limited understanding of the effects of several drivers of wood properties, such as climate variation, genetic material, and forest disturbances, among others, and highlight the need for further data collection efforts to better anticipate the quality attributes of the future wood fibre resource. We conclude by providing examples of promising new tools and technologies that will help move wood quality research forward by allowing (1) fast, efficient characterisation of wood properties, and (2) up-scaling predictions at the landscape level to inform forest management decisions.

This study investigates how the use of a Hitman ST300 acoustic sensor can help identify the best forest stands to be used as supply sources for the production of Machine Stress-Rated (MSR) lumber. Using two piezoelectric sensors, the ST300 measures the velocity of a mechanical wave induced in a standing tree. Measurements were made on 333 black spruce (Picea mariana (Mill.) BSP) trees from the North Shore region, Quebec (Canada) selected across a range of locations and along a chronosequence of elapsed time since the last fire (TSF). Logs were cut from a subsample of 39 trees, and sawn into 77 pieces of 38 mm × 89 mm cross-section before undergoing mechanical testing according to ASTM standard D-4761. A linear regression model was developed to predict the static modulus of elasticity of lumber using tree acoustic velocity and stem diameter at 1.3 m above ground level (R² = 0.41). Results suggest that, at a regional level, 92% of the black spruce trees meet the requirements of MSR grade 1650Fb-1.5E, whilst 64% and 34% meet the 2100Fb-1.8E and 2400Fb-2.0E, respectively. Mature stands with a TSF < 150 years had 11 and 18% more boards in the latter two categories, respectively, and therefore represented the best supply source for MSR lumber.