Stiffness is considered one of the most important structural properties for sawn timber used in buildings and laminated structures including mass timber elements. There is great potential to use plantation Eucalyptus timber for structural applications, and the successful development of a plantation timber supply chain for structural products will depend on the accurate selection and grading of the resource. In this study we aimed to investigate the suitability of non-destructive testing (NDT) to improve selection and grading of sawn boards sourced from a young E. nitens plantation. We studied 268 sawn boards traced from the tree through to final processing stages. We found high and positive correlations between stiffness (measured as dynamic modulus of elasticity) tested at each board processing stage through acoustic wave velocity (AWV) and the static board modulus of elasticity measured through mechanical testing on dressed boards. Position of the board in the stem and sawn board processing treatment significantly impacted board modulus of elasticity, indicating that early selection of logs would allow larger yield of stiffer boards. We investigated the grading of boards through the traditional Australian Standards using a visual-grading system and through AWV, finding a classification error of 82.5% and 45.2%, respectively. We developed a linear model which was used to re-classify the boards, obtaining a smaller classification error, including fewer boards being over-graded. Our results demonstrate that AWV can be used as an early selection method for structural boards and can also be employed to satisfactorily grade E. nitens plantation boards to be used in building structures and as elements of mass timber.
Thinning of forestry plantations is a common silviculture practice to increase growth rates and to produce larger dimension logs. The wood properties, basic density and stiffness, are key indicators of the suitability of timber for particular purposes and ultimately determine timber value. The impact of thinning operations on wood properties is, therefore, of considerable interest to forest growers and timber producers. To date, studies examining the impact of thinning on wood properties have produced variable results and understanding the consistency of the effects of thinning treatments across various sites for important plantation species is limited. Two non-destructive assessment techniques, drilling resistance and acoustic wave velocity, were used to examine the impact of thinning on basic density and stiffness in 19–21-year-old plantation grown Eucalyptus nitens across three sites. Commercial thinning to 300 trees ha−1 decreased the stiffness of standing trees and this effect was consistent across the sites. Reduction in stiffness due to thinning ranged from 3.5% to 11.5%. There was no difference in wood properties between commercially and non-commercially thinned trees to 300 trees ha−1 and no difference in wood properties when thinned to 500 trees ha−1. Basic density was not affected by thinning. The site had significant effects on both basic density and stiffness, which were lowest at the highest precipitation and highest elevation site. The results indicate that wood properties are influenced both by silviculture and site environmental differences. This knowledge can be used for the better management of E. nitens resources for solid wood production.
Thermo-hydro mechanical (THM) treatments and thermo-treatments are used to improve the properties of wood species and enhance their uses without the application of chemicals. This work investigates and compares the effects of THM treatments on three timber species from Tasmania, Australia; plantation fibre-grown shining gum (Eucalyptus nitens H. Deane and Maiden), plantation saw-log radiata pine (Pinus radiata D. Don) and native-grown saw-log timber of the common name Tasmanian oak (which can be any of E. regnans F. Muell, E. obliqua L’Hér and E. delegatensis L’Hér). Thin lamellae were compressed by means of THM treatment from 8 mm to a target final thickness of 5 mm to investigate the suitability for using THM-treated lamellas in engineered wood products. The springback, mass loss, set-recovery after soaking, dimensional changes, mechanical properties, and Brinell hardness were used to evaluate the effects of the treatment on the properties of the species. The results show a marked increase in density for all three species, with the largest increase presented by E. nitens (+53%) and the smallest by Tasmanian oak (+41%). E. nitens displayed improvements both in stiffness and strength, while stiffness decreased in P. radiata samples and strength in Tasmanian oak samples. E. nitens also displayed the largest improvement in hardness (+94%) with respect to untreated samples. P. radiata presented the largest springback whilst having the least mass loss. E. nitens and Tasmanian oak showed similar dimensional changes, whilst P. radiata timber had the largest thickness swelling and set-recovery due to the high water absorption (99%). This study reported the effects of THM treatments in less-known and commercially important timber species, demonstrating that the wood properties of a fibre-grown timber can be improved through the treatments, potentially increasing the utilisation of E. nitens for structural and higher quality timber applications.