The physical and mechanical properties of the reservoir bank slope are affected by the water–rock interaction. However, few studies considered the impact of long-term water–rock interaction on the evolution law of mesostructure. Therefore, in this study, the water–rock interaction test was conducted on a slightly weathered red-bed soft rock from the Three Gorges Reservoir area, considering the fluctuation in the reservoir water level. The corresponding pore structure parameters were measured and analyzed based on a scanning electron microscope (SEM) and digital image processing technology. The study showed that: (1) The pore size has been gradually increased, while the number of pores was increased initially and then decreased. Within 12 cycles, the maximum and average pore radius of the rock specimens was increased by 101.02% and 43.32%, respectively, and the porosity has been increased by 26.59%, whereas the number of pores decreased by 22.65%. This indicates the effect of water–rock interaction on the propagation of pores. (2) The pores were changed from oblate to slender by the water–rock interaction. The shape factor was decreased by about 15.79% within 12 cycles. In the meantime, the fractal dimension was increased from 1.20 to 1.28, and more complex structures of pores were observed. (3) The porosity evolution model for the red-bed soft rock was established based on the curve fitting technique. The results can be used as a reference to conceptualize the mesostructure damage of rocks under water–rock interaction.
25 August 2021 in Bulletin of Engineering Geology and the Environment
Changes in the micromorphology of joint surface under dry-wet cycling have a direct effect on the mechanical properties of the jointed rock masses, which in turn affects the deformation stability of the bank slope of a reservoir. In this study, we design and carry out a test that aims to quantity the effects of repeated rise and fall of a reservoir on the properties of a jointed rock masses. The results are as follows: first, the roughness, local gradient, and undulation of the joint surface gradually decreased under repeated dry-wet cycling. In addition, the height parameters and texture parameters showed a steep decrease followed by a slow decline. The deterioration was particularly obvious over the first 5 dry-wet cycles. Second, the roughness coefficient of the joint surface, the compressive strength of the face wall, and the basic friction angle were gradually reduced under dry-wet cycling. The shear strength of the jointed rock masses (obtained both quantitatively and experimentally) showed a deteriorating trend controlled by the deterioration of the micromorphology, the strength of the face wall, and the frictional properties of the joint surface. Finally, the dry-wet cycling process determined trends of changes in the microstructure parameters and mechanical properties of the joint surface. Our research results provide a good basis for the analysis of the deterioration and failure of rock masses within the hydrofluctuation belt of a bank slope.
26 November 2019 in Arabian Journal of Geosciences
There are a large number of fractured rock masses in the Three Gorges Reservoir area. Traditional reinforcement methods have disadvantages such as large engineering investment, high material consumption, and poor ecological environmental protection. Therefore, it is necessary to develop new environmentally friendly materials and methods to strengthen and control them. The microbial-induced carbonate precipitation (MICP) technology that has emerged in recent years has the characteristics of low carbon and environmental protection and has great prospects in the restoration and reinforcement of rock and soil materials. Therefore, Bacillus cereus extracted in situ from the Three Gorges Reservoir area is proposed to be used for MICP reinforcement of single-fractured sandstone, and its reinforcement mechanism is revealed by studying the macroscopic impermeability and shear performance improvement of the fractured rock sample after reinforcement, and the microstructure changes. The results show that after 10 cycles of grouting reinforcement, the fracture surface of the rock sample is well sealed, the permeability coefficient is reduced by two orders of magnitude, the shear stress is increased by 26%–40%, and the shear stiffness is increased by 70%. The shear stress–shear displacement curve shows the peak shear strength, and the residual shear strength also increases to a certain extent. The MICP process improves the mechanical properties of fractured rock samples from three aspects, namely, the cementation between sand grains and the fracture surface, the cementation effect between sand grains, and the filling effect of fractured rock samples. The shear failure surface of the samples after reinforcement is the recheck interface between the cementation body and the cementation interface. The relevant research results can provide references for the MICP reinforcement technology of fractured rock mass.