The application results of profile control and water plugging technology are highly related to the gelation time and strength of phenolic resin hydrogel. In this work, a hydrogel solution was prepared by fully mixing the prepared polymer solution with a crosslinker. The static gelation process of PFR hydrogel in ampoule bottles and porous media was analyzed by changes in the viscosity and residual resistance coefficient. Then, the dynamic gelation of the PFR hydrogel in porous media was tested using a circulating flow device, and the changes in viscosity and injection pressure were analyzed during the dynamic gelation process. Finally, the effects of the polymer concentration and crosslinker concentration on dynamic gelation were analyzed. The initial gelation time and final gelation time in porous media were 1–1.5 times and 1.5–2 times those in ampoule bottles under static conditions, respectively. The initial dynamic gelation time in porous media was 2–2.5 times and 1.5–2 times the initial static gelation times in ampoule bottles and porous media, respectively. The final dynamic gelation time was four times and two times the initial static gelation times in ampoule bottles and porous media, respectively. The production after dynamic gelation in porous media comprised hydrogel aggregates and water fluid, leading to a high injection pressure and low viscosity of the produced liquid. As the concentration of polymer and crosslinker increased, the dynamic gelation time was shortened and the gel strength was increased. In the dynamic gelation process in porous media, the phenol resin hydrogel could migrate deeply, but it was limited by the concentrations of the polymer and crosslinker. The results of subsequent water flooding showed that the polymer hydrogel had a good plugging ability after dynamic gelation. The deep reservoir could only be blocked off in the subsequent water flooding process when the migration of hydrogel happened in the dynamic gelation process.
8 August 2019 in Greenhouse Gases: Science and Technology
Supercritical carbon dioxide (CO2) is a promising working fluid for geothermal energy extraction due to its superior heat extraction capacity and high fluidity within reservoirs. However, significant thermal energy is lost during transportation along the production well. This study develops a mathematical model coupling heat transfer and CO2 compressibility to investigate strategies for improving heat transfer efficiency from the reservoir to the surface. The influence of mass flow rate (20 kg/s; 25 kg/s and 30 kg/s) and outlet back pressure (8 MPa; 9 MPa and 10 MPa) on system performance is evaluated. Results indicate that the amount of geothermal energy delivered to the surface increases linearly with mass flow rate. Compared to water, CO2 exhibits a 65.5% greater temperature drop along the wellbore but reduces the pressure drop by 50%. A lower outlet back pressure is recommended to enhance both heat transfer and operational safety. The model offers valuable insights into assessing the geothermal potential of depleted high-temperature gas reservoirs.
Cryogenic nitrogen fracturing is an attractive method for stimulating underground reservoir, since it could favorably induce complex fracture due to the huge temperature difference with lower injection pressure and with the replacement of current water‐based fracturing fluid. However, the concern about whether cryogenic nitrogen would be overheated remains unrevealed in the engineering environment with large wellbore length. In addition, reservoir stimulation results are also related with the pressure state at bottom hole. Therefore, in this study, a mathematical model was proposed to predict the radial heat transfer and its influence on vertical pressure transmission in the wellbore with cryogenic nitrogen as fracturing fluid. The model fully couples the heat transfer, hydraulics, and the compressibility of nitrogen, and then, the calculation results were presented and analyzed through a case study. According to the results, the temperature of nitrogen increases too fast under conventional engineering conditions, and it changes into gaseous state at the depth lower than 100 m. Finally, the temperature difference between nitrogen and formation rock becomes too minimal to induce thermal stress at bottom hole. Due to the fast temperature increase, the density of nitrogen decreases too much, and the vertical pressure increasing rate by liquid nitrogen (1.66 MPa/km) is merely 18.2% that in carbon dioxide fracturing (9.13 MPa/km). The results indicate that utilization of special casing with much larger thermal resistance is an indispensable approach to realize the feasibility and advantages of cryogenic nitrogen fracturing.
Gas channeling control is key to improving CO2-flooding efficiency. A traditional plugging system has disadvantages, such as poor adaptability and stability, leading to the poor plugging effect of CO2 channeling in heterogeneous reservoirs and difficulty in controlling the subsequent CO2 injection pressure. To achieve a significant plugging effect and effectively control the subsequent CO2 injection pressure, a heterogeneous physical model of gas channeling in a horizontal well was established, and plugging experiments were conducted using four different combinations of plugging agents during CO2 flooding. Three evaluation parameters were defined, including the temperature field variation coefficient (TFVC), medium-permeability diversion rate (MPDR), and subsequent injection pressure coefficient (SIPC). The plugging effect of different combinations of plugging agents during CO2 flooding in heterogeneous reservoirs was analyzed. The results show that the plugging effect after using a combination of plugging agents was significantly better than after using a single plugging agent, and different plugging agent combinations had distinct characteristics. The strong–medium–weak (S-M-W) combination had the best MPDR for subsequent CO2 flooding, but the SIPC was the highest. The strong–weak–strong–weak (S-W-S-W) and weak–strong–weak–strong (W-S-W-S) combinations could effectively control the SIPC. These results indicate that plugging using the S-W-S-W and W-S-W-S combinations can achieve an effective plugging effect and reasonably control the subsequent CO2 injection pressure. This work provides a personalized design scheme for effective gas channeling control and maintenance of appropriate injection pressure during CO2 flooding in heterogeneous reservoirs.