To improve practical application of modern bamboo structures, strengthening the bamboo engineering material is necessary to overcome insufficient stiffness. As an essential step in developing fibre-reinforced polymer–bamboo engineering material composite structures aimed at increasing the structural stiffness, the bonding behaviour at the interface of the fibre-reinforced polymer and bamboo engineering materials should be investigated in detail because currently there is a lack of research. In this article, bonding behaviour is studied between basalt fibre-reinforced polymer bar and bamboo engineering material including laminated and reconstituted bamboo and between basalt fibre-reinforced polymer sheets and laminated bamboo. Failure patterns are categorized, and the load–slip curves are discussed. Based on the failure pattern and strain variation, recommended bond lengths were proposed for the basalt fibre-reinforced polymer bar–bamboo engineering material and basalt fibre-reinforced polymer sheet–laminated bamboo composite specimens, respectively. In addition, a simplified three-phase bond–slip model was proposed for the basalt fibre-reinforced polymer bar–bamboo engineering material composite specimen.
12 August 2020 in Advances in Structural Engineering
Mechanical properties of fiber-reinforced polymer rebar and bond behavior between the fiber-reinforced polymer rebar and concrete are highly related to rib parameters, including rib depth and rib spacing. Therefore, rib parameters should be taken into account when fiber-reinforced polymer bars are used as the structure reinforcement. In this article, the tensile properties of glass-fiber-reinforced polymer rebars with different rib depths and rib spacings are tested. The influences of different rib depths and rib spacings on the bond behavior between glass-fiber-reinforced polymer rebar and concrete are investigated by pull-out test. Experimental results show that the rib depth has a distinctive effect on the ultimate tensile strength, elastic modulus, and ultimate elongation of glass-fiber-reinforced polymer rebar. The tensile strength and elastic modulus of glass-fiber-reinforced polymer rebar with shallow rib are remarkably higher than those of glass-fiber-reinforced polymer bars with deep rib. However, compared with the glass-fiber-reinforced polymer bars with shallow rib, the glass-fiber-reinforced polymer bars with deep rib contribute larger bond strength with concrete. Besides, the bond strength and basic anchorage length are predicted by taking rib depth and rib spacing into account. A modified Bertero–Popov–Eligehausen model is adopted to simulate the bond stress–slip behavior, and the ascending branch of bond stress–slip curve expressed by rib depth and rib spacing is also proposed. The calculated results are in good agreement with the test ones.
This article proposes a basalt fiber-reinforced plastic–bamboo (BFRP-bamboo) composite beam consisting of BFRP sheet and laminated bamboo, aiming at fully utilizing advantages of bamboo and BFRP to improve the mechanical behavior of the laminated bamboo beam. A two-step test program is involved: (1) double shear test for bonding behavior between the BFRP and laminated bamboo and (2) loading test for mechanical behaviors of both laminated bamboo and BFRP-bamboo composite beams. Parameters affecting the bonding behavior are firstly concluded as the coated surface resin, types of bonding materials, and interfacial treatment. Then, the failure patterns of both laminated bamboo and BFRP-bamboo composite beam are discussed based on experimental observations. Key mechanical indexes, including the yield force, yield displacement, ultimate load, ultimate displacement, ductility, and stiffness, are analyzed based on load–displacement curves of tested specimens. Besides, theoretical analyses of bearing capacity of the BFRP-bamboo composite beam, featured as fracture failure, are conducted.
Until now, the systematical and comprehensive strengthening techniques have not been formed for the bamboo structure. Under such background, this paper aims to explore the effects of the application of the nonprestressed and prestressed basalt fiber-reinforced polymer (BFRP) bars on the flexural performance of the beams made of the laminated bamboo and reconstituted bamboo materials. Two series of four-point bending tests were thus conducted. In the first series of tests, the pure laminated bamboo beam and the laminated bamboo beam applied with nonprestressed BFRP bar were compared. Test results showed that the ultimate load and deformation capacity of the laminated bamboo beam was improved due to the existence of the BFRP bar. In the second series of tests, the reconstituted bamboo beams applied with nonprestressed and prestressed BFRP bars were compared. It is found that the ultimate load of the reconstituted bamboo beam was not improved by the application of the prestressed force. The further analysis related to the prestress loss demonstrated that the prestress loss before the release of the prestressed BFRP bar could reach up to 31.8–37.3% compared with the design initial prestressed stress. The prestress loss caused by the elastic deformation of the bamboo beam can be neglected. For all tested specimens, the plane section assumption was acceptable and the position of the neutral axis of the beam gradually moved down with the increase of the applied load.
In order to accord well with the requirements of sustainable development and green construction, a cross‐laminated bamboo composed of an odd number of orthogonally oriented layers of bamboo scrimber is proposed in this paper. Adjacent bamboo layers are face‐bonded by structural adhesives under pressure. The uniform mechanical and physical properties can be obtained through the orthogonal layup. Flexural performances of three groups of one‐way CLB slabs and two groups of one‐way CLB slabs strengthened with CFRP grids were investigated via four‐point monotonic loading configuration until failure. Experimental parameters of thickness of the layer, number of layers, and manufacturing processes of CFRP grids were taken into consideration. Experimental observations showed that the failure of the CLB slab was brittle, and different failure modes were found in the CLB slab with CFRP grids via different manufacturing processes. Test results showed that the load‐carrying capacity increased with the thickness of the layer, number of layers, and application of CFRP grids pressed in the bamboo layer, but the CFRP grids pressed in the interface of adjacent bamboo layers weakened the load‐carrying capacity. The strain analysis demonstrated that the compression region was utilized with more efficiency via CFRP grids pressed in the bamboo layer, and the plane cross section assumption is suitable for both CLB slab and CLB slab strengthened with CFRP grids. A theoretical calculation method of flexural load‐carrying capacity was proposed for the CLB slab, the accuracy of which was proved.
Cross-laminated bamboo (CLB) have a high strength to weight ratio and stable bidirectional mechanical properties. Inspired by the investigation on cross-laminated timber (CLT) rocking walls, CLB rocking walls with conventional friction dampers (CFDs) are studied in this paper. To investigate the mechanical properties of the CLB rocking wall, seven tests are conducted under a cyclic loading scheme, and different test parameters, including the existence of the CFDs, the moment ratio, and the loading times, are discussed. The test results show a bilinear behavior of the CLB rocking wall. The small residual displacements of the CLB rocking wall demonstrate an idealized self-centering capacity. The cumulative energy dissipation curves indicate that the energy dissipation capacity of the CLB rocking wall can be greatly improved with CFDs. The limit states of the CLB rocking wall under a lateral force are proposed based on the strains, stress, and damage level of the CLB material and posttensioned rebar. In addition, an analytical model of the CLB rocking wall is developed based on the proposed limit states of the CLB rocking wall to evaluate the hysteretic response of the CLB rocking wall, and the model is validated by the experimental data. The comparison results show the potential value of the analytical model for engineering design.