Silicate composites have very low conductivity in general. It is possible to achieve an electrical resistivity decrease by adding an electro-conductive filler. The conductive mixture consists of cementitious binder, various types of silica sand, and graphite-based conductive fillers. One of the research focusses is partial substitution of ordinary raw materials by alternative components (waste materials by-products and secondary raw materials) and its influence on composite properties. The alternative components studied were fly ash as a partial binder replacement, waste graphite from two different sources and steel shavings as a substitute for conductive filler. Resistivity of cured conductive silicate-based specimens was analysed in relation to changes in physico-mechanical properties in context of microstructural changes in the hardened cementitious matrix (by optical and scanning electron microscopy with energy disperse analysis). Partial substitution of cement by fly ash was found to reduce the electrical resistivity of the composite. Some of the waste graphite fillers significantly reduce the resistivity of the cement composite and increase the compressive strength. It was proven, that is possible to replace primary conductive fillers by secondary raw materials.
The use of superabsorbent polymers (SAP) in construction is a relatively new trend, and not a completely explored area. However, SAP itself has been on the market for over 80 years. SAPs have a cross-linked three-dimensional structure, thanks to which they have the unique ability to absorb extreme amounts of water, up to a hundred times their weight. By using this property, it is possible to prevent water losses, which is important at the time of maturation in cementitious building materials. When there is a lack of water needed for hydration processes, the physical and mechanical properties deteriorate. The subject of this article is to determine the possible positive effect of the presence of SAP in the cement matrix in order to optimize the parameters of silicate composites for 3D printing. For this purpose, a special methodology was compiled consisting of tests through which it is possible to assess the suitability of the tested mixtures for 3D printing. This methodology consists of determining consistency, volumetric weight, ultrasonic analysis, buildability, X-ray diffraction, flexural tensile and compressive strength. For determining of buildability and ultrasonic analysis new methodologies were created in this research in order to be suitable for the 3D printing materials. Last but not least, efforts are also being made to increase the incorporation of secondary raw material (fly ash) in order to reduce the environmental impact of industrial production and, conversely, to increase its sustainability while maintaining or improving the mechanical–physical parameters of building materials. From the results presented in this paper it is apparent, that created methodology is efficient for determining properties of 3D printable mixtures. SAPs also significantly influenced properties of these mixtures. Mainly buildability and flexural tensile strength (by up to 30%) were increased and volumetric weight was decreased (by up to 5%).
Electroconductive cement-based composites are modern materials that are commonly used in many industries such as the construction industry, among others. For example, these materials can be used as sensors for monitoring changes in construction, grounding suspension, and resistance heating materials, etc. The aim of the research presented in this article is to monitor the impact of carbon particle character on cement-based electroconductive composites. Four types of graphite were analyzed. Natural and synthetic types of graphite, with different particle sizes and one with improved electrically conductive properties, were tested. For the analysis of the electrical conductivity of powder raw materials, a new methodology was developed based on the experience of working with these materials. Various types of graphite were tested in pure cement paste (80% cement, 20% graphite) as well as in a composite matrix, which consisted of cement (16.8%), a mixture of silica sand 0–4 mm (56.4%), graphite filler (20.0%) ground limestone (6.7%) and super plasticizers (0.1%). The resistivity and physical-mechanical properties of the composite material were determined. Furthermore, the resistivity of the test samples was measured with a gradual decrease in saturation. It may be concluded that graphite fillers featuring very fine particles and high specific surface are most suitable and most effective for creating electrically conductive silicate composites. The amount, shape and, in particular, the fineness of the graphite filler particles thus creates suitable conditions for the creation of an integrated internal electricity-conductive network. In the case of the use of a coarse type of graphite or purely non-conductive fillers, the presence of an electrolyte, for example, in the form of water, is necessary to achieve a low resistivity. Samples with fine types of graphite fillers achieved stable resistivity values when the sample humidity changed. The addition of graphite fillers caused a large decrease in the strength of the samples.
Epoxy resins are currently used in many areas of construction, such as resistant coatings, anchors, fibre-reinforced polymer (FRP) composites, grouts, etc. This paper deals mainly with epoxy composites that can be applied during the rehabilitation of concrete constructions. The influence of a filler type on epoxy thermoset composites was monitored, whilst three different types of epoxy resin were used in order to achieve a better representation and confirmation of the results. During the testing of fillers, these were mainly secondary raw materials, including pre-treated hazardous waste (neutralisation sludge), representing various shapes and sizes of particle, while their amount in the epoxy matrix was chosen with regard to optimal viscosity and workability. Physical and mechanical parameters, like compressive and flexural strengths, cohesion with the concrete and thermal expansion of the epoxy composites containing various fillers were determined. The microstructure of epoxy composites with a different filler type and chemical resistance against chemical aggressive media were all monitored. The microstructure of epoxy composites was monitored using scanning electron microscopy (SEM) supported by energy-dispersive X-ray spectroscopy (EDX). Computed tomography (CT) was also used for the evaluation of the cohesion of the epoxy composites with concrete and dispersion of the filler in the epoxy matrix.
1 July 2021 in Construction and Building Materials