Virtual space vector pulsewidth modulation (VSVPWM) for the neutral-point (NP)-clamped three-level inverter is briefly reviewed in this paper, as well as its carrier-based realization. The carrier-based VSVPWM (CB_VSVPWM) is featured with dual modulation waves and a single carrier. Although CB_VSVPWM can make NP voltage unfluctuating in theory, it does not have the NP voltage recovery ability. In practice, due to the effect of nonidea factor effects, NP voltage may shift. Thus, active NP voltage control (ANPVC) is necessary. To achieve that, three ANPVC approaches are proposed based on CB_VSVPWM in this paper. The NP voltage control ability of CB_VSVPWM with ANPVC is analyzed. Finally, comprehensive experiments are carried out to verify the feasibility of the proposed method.

A novel carrier-based discontinuous pulsewidth modulation (CB_DPWM) strategy for T-type three-level converter is proposed in this article. Because one significant advantage of the proposed CB_DPWM is the reduction of common mode voltage (CMV), it is named as RCMV_CB_DPWM hereafter. It also can reduce switching loss and remove dc offset from the neutral point voltage (NPV) simultaneously. RCMV_CB_DPWM has two design freedoms, one is modulation wave and the other is carrier wave. By injecting zero sequence voltage properly, the corresponding clamping mode can be acquired. Moreover, reduced CMV can be achieved by arranging carrier wave flexibly. The integrity of RCMV_CB_DPWM is analyzed as well as its NPV self-equilibrium ability, and an active NPV control method is then introduced. Moreover, its realization is discussed briefly. Finally, the experiments are carried out to verify the effectiveness of the proposed method.

The parallel three-phase grid-connected converters (GCCs) with common dc and ac buses can increase the system power level effectively. However, zero sequence circulating current (ZSCC) will occur inevitably. In this paper, the mechanisms and characteristics of ZSCC in two parallel three-phase GCCs are first investigated based on three typical cases. From the analysis, it was found that not all ZSCC can be suppressed. Generally speaking, ZSCC caused by inconsistent modulation voltages between modules cannot be effectively handled. And ZSCC caused by different injected zero sequence voltages (ZSVs) or asynchronous carriers can be suppressed. Based on the theoretical analysis, identical ZSV injection and carrier synchronization methods without communication are, thus, proposed to suppress ZSCC at the source, which are easily implemented without adding any hardware. Finally, the theoretical analysis and the effectiveness of the proposed methods on ZSCC suppression are well-verified by experiments.

In this paper, a novel discontinuous pulsewidth modulation (DPWM) modulation strategy for a neutral-point-clamped (NPC) three-level converter (TLC) is proposed to reduce the switching loss, reduce common-mode voltage (CMV), and remove dc offset from the neutral-point (NP) voltage simultaneously, which is named as RCMV_DPWM. Based on the space vector diagram with reduced CMV, all clamping modes under RCMV_DPWM are revealed. Then, the NP voltage is controlled by selecting proper clamping mode. The realization of RCMV_DPWM is also discussed. Moreover, the performances of RCMV_DPWM are analyzed and compared with other PWM strategies in term of the NP voltage ripple, switching loss, and waveform quality. Finally, the feasibility and superiority of RCMV_DPWM are verified by experiments.

In order to reduce switching loss of neutral point clamped three-level inverter (NPCTLI), generally discontinu-ous pulse width modulation (DPWM) is used. But it can result in DC offset and AC ripple on neutral point (NP) voltage. So a novel pulse sequence DPWM (NPSDPWM) is proposed to reduce switching loss and control NP voltage simultaneously in this paper. NP voltage is controlled by choosing proper clamping modes. To avoid unexpected switching action during changing clamping mode, an improved pulse se-quence is also presented. The switching loss and NP voltage ripple of NPSDPWM, traditional and proposed DPWM in pre-vious literature are compared respectively. The experimental results show that NPSDPWM has well NP voltage control ability and the switching losses are reduced effectively.

Vienna rectifier is a boost-type rectifier with unidirectional energy flow, which is widely used in industrial applications. To improve the power density of the Vienna rectifier, the high switching frequency is seen as an inevitable cause of larger switching losses. To reduce switching losses, discontinuous pulsewidth modulation (DPWM) is usually used. But this will cause dc offset and ac ripple on neutral point (NP) voltage. To overcome these problems, a carrier-based DPWM (CB_DPWM) method suitable for a Vienna rectifier with simple implementation is proposed to simultaneously reduce switching losses and control NP voltage. By selecting the proper clamping mode, NP voltage can be well controlled. To avoid unnecessary switching actions while switching clamping mode, an improved PWM sequence based on carrier type is given. The comparisons among space vector PWM, DPWM 1–3 presented by Zhang et al. , and the proposed CB_DPWM are presented with the corresponding simulation and experimental results, and the superiority of the proposed strategy is verified in terms of reducing switching loss and controlling NP voltage.