Tian-Hua Liu

Prof. Tian-Hua Liu

National Taiwan University of Science and Technology
orcid

Research Focus & Metrics

Academic Career Length

37Years (1990-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 March 2013 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
CLCheng-Kai Lin
Cheng-Kai Lin
Tian-Hua LiuTian-Hua Liu
Tian-Hua Liu
JYJen-Te Yu
Jen-Te Yu
LFLi-Chen Fu
Li-Chen Fu
CHChieh-Fu Hsiao
Chieh-Fu Hsiao
A model-free predictive current control (PCC) of interior permanent-magnet synchronous motor (IPMSM) drive systems based on a current difference detection technique is proposed. The model-based PCC (MBPCC) of IPMSM requires knowledge of parameters such as resistance, q-axis inductance, and extended back EMF. This paper develops a new model-free approach that alleviates the need for excessive prior knowledge about the system and only utilizes the stator currents as well as the current differences corresponding to different switching states of the inverter. Despite the salient difference of the proposed approach, it adopts a measure similar to that in the MBPCC approach to obtain the next switching state of the inverter by minimizing a cost function. It is noteworthy that the proposed method is easy to implement due to its simplicity and free of any multiplication operation. For comparison purposes, a digital signal processor, TMS320LF2407, is used to execute the two aforementioned current control techniques. Several experimental results show that the proposed method can significantly improve the current-tracking performance.

1 January 1993 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
Tian-Hua LiuTian-Hua Liu
Tian-Hua Liu
JFJen-Ren Fu
Jen-Ren Fu
TLT.A. Lipo
T.A. Lipo

7 November 2002 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
SSS. Sirisukprasert
S. Sirisukprasert
JLJih-Sheng Lai
Jih-Sheng Lai
Tian-Hua LiuTian-Hua Liu
Tian-Hua Liu
This paper proposes a novel modulation technique to be applied to multilevel voltage-source converters suitable for high-voltage power supplies and flexible AC transmission system devices. The proposed technique can generate output stepped waveforms with a wide range of modulation indexes and minimized total voltage harmonic distortion. The main power devices switch only once per cycle, as is suitable for high-power applications. In addition to meeting the minimum turn-on and turn-off time requirements for high-power semiconductor switches, the proposed technique excludes from the synthesized waveform any pulses that are either too narrow or too wide. By using a systematic method, only the polarities and the number of levels need to be determined for different modulation levels. To verify the theory and the simulation results, a cascaded converter-based hardware prototype, including an 8-b microcontroller as well as modularized power stage and gate driver circuits, is implemented. Experimental results indicate that the proposed technique is effective for the reduction of harmonics in multilevel converters, and both the theoretical and simulation results are well validated.

1 January 1993 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
EME. Muljadi
E. Muljadi
YZY. Zhao
Y. Zhao
Tian-Hua LiuTian-Hua Liu
Tian-Hua Liu
TLT.A. Lipo
T.A. Lipo
The most common practice for starting a single-phase induction machine (SPIM) is to install a starting capacitor in series with the auxiliary winding. In some applications, two capacitors are used. One is used during the starting period to help create the starting torque. The other one is used during the running condition to improve efficiency. The possibility of using an electronic switch in parallel with the running capacitor, thereby providing the equivalent of a starting capacitor, is discussed. The capacitor is shorted during each cycle to vary the effective size of the AC capacitor. By using this method, only one capacitor is used for both the starting and running condition, and a starting performance similar to that of the conventional method using two capacitors can be obtained.

23 May 2011 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
KNKhiem Nguyen-Duy
Khiem Nguyen-Duy
Tian-Hua LiuTian-Hua Liu
Tian-Hua Liu
DCDer-Fa Chen
Der-Fa Chen
JHJohn Y. Hung
John Y. Hung
The matrix converter system is becoming a very promising candidate to replace the conventional two-stage ac/dc/ac converter, but system reliability remains an open issue. The most common reliability problem is that a bidirectional switch has an open-switch fault during operation. In this paper, a matrix converter driving a speed-controlled permanent-magnet synchronous motor is examined under a single open-switch fault. First, a new fault-detection method is proposed using only the motor currents. Second, a novel fault-tolerant switching strategy is presented. By treating the matrix converter as a two-stage rectifier/inverter, existing modulation techniques for the inverter stage can be reused, whereas the rectifier stage is modified by control to counteract the fault. However, the proposed techniques require no additional hardware devices or circuit modifications to the matrix converter. Experimental results show that the proposed method can maintain the motor speed with a maximum ripple of 2%-a fivefold improvement over the uncompensated system. The proposed method therefore offers a very economical and effective solution for the matrix converter fault tolerance problem.

16 July 2007 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
JSJi-Liang Shi
Ji-Liang Shi
Tian-Hua LiuTian-Hua Liu
Tian-Hua Liu
YCYung-Chi Chang
Yung-Chi Chang
This paper proposes a novel sensorless position control system for an interior permanent-magnet synchronous motor. In this paper, a novel rotor position/velocity estimation technique is proposed. This estimation technique only relates to the slopes of the stator currents and does not relate to the parameters or operating conditions of the motor. Neither an extra circuit nor an external high-frequency exciting signal is required here as compared to other position estimation techniques. In addition, the proposed estimator works well in transient, steady-state, and standstill conditions. As a result, the proposed method is very robust and useful. To improve the performance of the position-control system, an optimal controller is proposed. By using this controller, a fast transient response, good load disturbance rejection capability, and satisfactory tracking ability can be achieved. A digital signal processor, TMS-320-LF-2407, is used to execute the rotor position/velocity estimation, the current-loop control, the velocity-loop control, and the position-loop control. As a result, a fully digital position-control system is achieved. Several experimental results validate the theoretical analysis.