The paper considers the protection of critical radio-electronic equipment (REE) from ultrashort pulses (USP) by means of modal filters (MFs). A new approach to improve modal filtration by using reflection symmetry is analyzed. The results of a sophisticated research into protective devices based on reflection symmetric MFs are presented: improving the characteristics of four MFs through optimization both by one and simultaneously by several criteria; calculating the per-unit-length time delays matrix of a reflection symmetric MF using the obtained analytical expressions; calculating the time and frequency responses of an MF with and without losses in conductors and dielectric; developing the laboratory evaluation board; analyzing the effect of moisture protection on the characteristics; analyzing the features of reflection symmetry structures; comparing microstrip and reflection symmetric four-conductor MFs. The obtained results allow us to argue that the reflection symmetric MF protects REE from a USP due to its decomposition into a sequence of pulses with pairwise equalized voltage amplitudes and close time intervals between decomposition pulses with an attenuation coefficient of four times with a controlled bandwidth of a useful signal. This research helps take advantage of the possibilities of using the symmetry to improve modal filtering and opens the ways to create a large number of new MF designs, applying only the principles of the symmetry described in the work.

For the first time, the paper considers in a unified work the possibility of the appearance of additional pulses in various structures based on modal filtration technology, which is used to improve protection against ultrashort pulses (USP). We analyzed meander lines (ML) with broad-side coupling, structures with modal reservation (MR), reflection symmetric MLs, and modal filters (MF) with a passive conductor in the reference plane cutout and obtained the following results. It was found that the main reason for the additional pulses to appear in these structures is the introduction of asymmetry (of the cross-section, boundary conditions, and excitation). It is theoretically and experimentally established that additional pulses are a new resource for increasing the efficiency of protective devices with modal decomposition, but the highest effectiveness could be achieved through careful optimization.

This work is devoted to the research of new asymmetry effects in symmetric protective structures with triple modal reservation. We analyzed the structures with different cross-sectional locations of the reference conductor: in the center (unshielded structure), around (shielded structure), at the top and bottom (multilayer printed circuit board), and in the form of side polygons (double-sided printed circuit board). First, a preliminary quasi-static simulation was performed in the range of parameters. It was revealed that in all structures, except for the shielded one (in the form of a cable), the deviations of the output voltage amplitude, bandwidth, and frequency of the first resonance were insignificant, whereas in the shielded structure there were significant deviations in the time and frequency responses. The attenuation of the output voltage in relation to the input for each structure was also estimated. In addition, we performed a parametric optimization of the structures under consideration using a heuristic search, which made it possible to improve their characteristics. Finally, the switching order between the conductors in these structures with the original and optimized parameter sets was investigated in detail. The optimal conductor switching order in the case of a component failure was determined, and the best (according to protective characteristics) parameter configuration for each structure was found.

The study considers the problem of ensuring electromagnetic compatibility of EMI‐based functional destruction means with other radioelectronic equipment as part of a complex for countering unmanned aerial vehicles. To solve this problem, it is proposed to create a methodology that combines a set of diverse approaches and methods. This study focuses on the use of hollow and thin passive conductors, the use of a magnetodielectric in a reflection symmetric modal filter, the use of reflection symmetric structures for decomposing the train of ultrashort pulses (USP), and the use of a meander line as a protective means against USPs. The main results that are expected to be obtained using the proposed approaches and methods are outlined.

The paper presents a comparative analysis of two new devices for protection against high-power ultrashort pulses (USPs): a four-conductor microstrip modal filter (MF) and a reflection symmetric MF, performed for the first time. These structures were simulated using a quasistatic approach with an increase of the separation between conductors from 200 to 800 μm. We provide a comparison of time and frequency characteristics and give the results of the qualitative comparison of the presented MFs by a number of attributes, which allow us to determine the advantages and disadvantages of each device. The results are useful for further research and proper use of protection means against USPs, which are based on stripe structures.

The paper considers the protection of radio-electronic equipment against ultrashort pulses (USP) by means of modal filters (MFs). The new structure of reflection symmetric MF structure is analyzed. It is reflection symmetric MF with an internal two-layer reference conductor. The results of a quasi-static and electrodynamic analysis of the reflection symmetric MF under influence of the USP, without and with taking into account the losses are presented. Consistency of results are obtained. The results are useful for further research, since the implementation of the reflection symmetric MF in such configuration is appropriate for further implementation.