Usama Kandil

Dr. Usama Kandil


Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 June 2015 in Polymers
Verified
Journal Article
Open access
PDF file
EBElisa Borowski
Elisa Borowski
ESEslam Soliman
Eslam Soliman
UKUsama Kandil
Usama Kandil
Mahmoud Reda TahaMahmoud Reda Taha
Mahmoud Reda Taha
Carbon fiber reinforced polymer (CFRP) laminates exhibit limited fracture toughness due to characteristic interlaminar fiber-matrix cracking and delamination. In this article, we demonstrate that the fracture toughness of CFRP laminates can be improved by the addition of multi-walled carbon nanotubes (MWCNTs). Experimental investigations and numerical modeling were performed to determine the effects of using MWCNTs in CFRP laminates. The CFRP specimens were produced using an epoxy nanocomposite matrix reinforced with carboxyl functionalized multi-walled carbon nanotubes (COOH–MWCNTs). Four MWCNTs contents of 0.0%, 0.5%, 1.0%, and 1.5% per weight of the epoxy resin/hardener mixture were examined. Double cantilever beam (DCB) tests were performed to determine the mode I interlaminar fracture toughness of the unidirectional CFRP composites. This composite material property was quantified using the critical energy release rate, GIC. The experimental results show a 25%, 20%, and 17% increase in the maximum interlaminar fracture toughness of the CFRP composites with the addition of 0.5, 1.0, and 1.5 wt% MWCNTs, respectively. Microstructural investigations using Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS) verify that chemical reactions took place between the COOH–MWCNTs and the epoxy resin, supporting the improvements experimentally observed in the interlaminar fracture toughness of the CFRP specimens containing MWCNTs. Finite element (FE) simulations show good agreement with the experimental results and confirm the significant effect of MWCNTs on the interlaminar fracture toughness of CFRP.

18 June 2014 in Materials
Verified
Journal Article
Open access
PDF file
ESEslam Soliman
Eslam Soliman
UKUsama Kandil
Usama Kandil
Mahmoud Reda TahaMahmoud Reda Taha
Mahmoud Reda Taha
This investigation examines the role of carboxyl functionalized multi-walled carbon nanotubes (COOH-MWCNTs) in the on- and off-axis flexure and the shear responses of thin carbon woven fabric composite plates. The chemically functionalized COOH-MWCNTs were used to fabricate epoxy nanocomposites and, subsequently, carbon woven fabric plates to be tested on flexure and shear. In addition to the neat epoxy, three loadings of COOH-MWCNTs were examined: 0.5 wt%, 1.0 wt% and 1.5 wt% of epoxy. While no significant statistical difference in the flexure response of the on-axis specimens was observed, significant increases in the flexure strength, modulus and toughness of the off-axis specimens were observed. The average increase in flexure strength and flexure modulus with the addition of 1.5 wt% COOH-MWCNTs improved by 28% and 19%, respectively. Finite element modeling is used to demonstrate fiber domination in on-axis flexure behavior and matrix domination in off-axis flexure behavior. Furthermore, the 1.5 wt% COOH-MWCNTs increased the toughness of carbon woven composites tested on shear by 33%. Microstructural investigation using Fourier Transform Infrared Spectroscopy (FTIR) proves the existence of chemical bonds between the COOH-MWCNTs and the epoxy matrix.

1 January 2002 in International Journal of Polymeric Materials and Polymeric Biomaterials
Verified
Journal Article
Closed access
SSS. M. Sayyah
S. M. Sayyah
ZEZ. A. El-Shafiey
Z. A. El-Shafiey
MEM. A. El-Sockary
M. A. El-Sockary
UKUsama Kandil
Usama Kandil
Benzylidene malononitrile (BMN) monomer was prepared from the condensation of benezaldehyde with malononitrile in absolute ethanol as a reaction medium using few drops of piperidine as a catalyst at the reflux temperature for one hour. This monomer (BMN) was copolymerized with methyl methacrylate (MMA) by solution polymerization technique in the presence of benzoyl peroxide as a free radical initiator using dimethyl formamide as a reaction medium in a sealed tube under a nitrogen atmosphere at 65°C. The Kelen-Tudös and Fineman-Ross were used to determine the copolymerization parameters of MMA (M 1 ) and BMN (M 2 ) monomers. It was found that, the reactivity ratios r 1 and r 2 for MMA and BMN are equal to 2.45, 0.12 - 0.05 respectively. Alfrey Price (Q) and (e) values were calculated and the obtained data indicated that the copolymer structure is a block system. Also, infrared, 1 H-NMR and UV-visible spectroscopic studies for the obtained copolymer were performed. Further UV-visible studies of the PMMA film blended with 1% by weight of the prepared MMA-BMN copolymer were carried out before and after irradiation with different gamma doses in the range from 0-100 KGy.

10 September 2016 in Nanomaterials
Verified
Journal Article
Open access
PDF file
ASahmad Mohamed al sabagh
ahmad Mohamed al sabagh
ETEman Taha
Eman Taha
UKUsama Kandil
Usama Kandil
GNGamal-Abdelnaser Nasr
Gamal-Abdelnaser Nasr
Mahmoud Reda TahaMahmoud Reda Taha
Mahmoud Reda Taha
In this work, we report the potential use of novel carbon nanofibers (CNFs), dispersed during fabrication of glass fiber composites to monitor damage propagation under static loading. The use of CNFs enables a transformation of the typically non-conductive glass fiber composites into new fiber composites with appreciable electrical conductivity. The percolation limit of CNFs/epoxy nanocomposites was first quantified. The electromechanical responses of glass fiber composites fabricated using CNFs/epoxy nanocomposite were examined under static tension loads. The experimental observations showed a nonlinear change of electrical conductivity of glass fiber composites incorporating CNFs versus the stress level under static load. Microstructural investigations proved the ability of CNFs to alter the polymer matrix and to produce a new polymer nanocomposite with a connected nanofiber network with improved electrical properties and different mechanical properties compared with the neat epoxy. It is concluded that incorporating CNFs during fabrication of glass fiber composites can provide an innovative means of self-sensing that will allow damage propagation to be monitored in glass fiber composites.

8 March 2017 in Polymers
Verified
Journal Article
Open access
PDF file
ASahmad Mohamed al sabagh
ahmad Mohamed al sabagh
ETEman Taha
Eman Taha
UKUsama Kandil
Usama Kandil
AAAhmed Awadallah
Ahmed Awadallah
GNGamal-Abdelnaser M. Nasr
Gamal-Abdelnaser M. Nasr
Mahmoud Reda TahaMahmoud Reda Taha
Mahmoud Reda Taha
Glass fiber reinforced polymer (GFRP) composites are widely used in infrastructure applications including water structures due to their relatively high durability, high strength to weight ratio, and non-corrosiveness. Here we demonstrate the potential use of carbon nanoparticles dispersed during GFRP composite fabrication to reduce water absorption of GFRP and to enable monitoring of moisture damage propagation in GFRP composites. GFRP coupons incorporating 2.0 wt % carbon nanofibers (CNFs) and 2.0 wt % multi-wall carbon nanotubes (MWCNTs) were fabricated in order to study the effect of moisture damage on mechanical properties of GFRP. Water absorption tests were carried out by immersing the GFRP coupons in a seawater bath at two temperatures for a time period of three months. Effects of water immersion on the mechanical properties and glass transition temperature of GFRP were investigated. Furthermore, moisture damage in GFRP was monitored by measuring the electrical conductivity of the GFRP coupons. It was shown that carbon nanoparticles can provide a means of self-sensing that enables the monitoring of moisture damage in GFRP. Despite the success of the proposed technique, it might not be able to efficiently describe moisture damage propagation in GFRP beyond a specific threshold because of the relatively high electrical conductivity of seawater. Microstructural investigations using Fourier Transform Infrared (FTIR) explained the significance of seawater immersion time and temperature on the different levels of moisture damage in GFRP.

3 November 2011 in Materials and Structures
Verified
Journal Article
Closed access
PDF file
ESEslam M. Soliman
Eslam M. Soliman
UKUsama Kandil
Usama Kandil
Mahmoud Reda TahaMahmoud Reda Taha
Mahmoud Reda Taha