This paper presents an innovative electronically controlled suspension system installed on a real car and used as a test bench. The proposed setup relies on a sensor network that acquires a large real-time dataset collecting the car vibrations and the car trim and, through a new controller based on a recently proposed theory developed by the authors, makes use of adjustable semi-active magneto-rheological dampers. A BMW series 1 is equipped with such an integrated sensors-controller-actuators device and an extensive test campaign, in real driving conditions, is carried out to evaluate its performance. Thanks to its strategy, the new plant enhances, at once, both comfort and drivability of the car, as field experiments show. A benchmark analysis is performed, comparing the performance of the new control system with the ones of traditional semi-active suspensions, such as skyhook devices: the comparison shows very good results for the proposed solution.
Energy harvesting represents one of the recent challenging subjects related to vibration and control. The scale of energy harvesters and storage can involve a wide power range, and the scale of some milliwatt is the elective field of piezoelectric applications. This paper investigates the power frontiers of the piezoelectric-based harvesters applied to automotive units. The analysis, supported by experimental data, aims at estimating the upper bound of the specific power of this technology for powering small devices on board cars. Passive optimally tuned piezoelectric harvester and semi-active controlled ones are compared, based on a new control strategy named VFC-Variational Feedback Control, recently developed by the authors. This new technique makes it possible to increase the total energy storage drained from car vibrations. However, the real advantage for their use relies on a sharp balance between the harvested power and the costs for the additional hardware mass transport. Numerical simulations of circuitry and experimental vibration data provides references to assess the energy convenience in installing this type of devices on board.
The study of the rolling tyre is a problem framed in the general context of nonlinear elasticity. The dynamics of the related phenomena is still an open topic, even though few examples and models of tyres can be found in the technical literature. The interest in the dissipation effects associated with the rolling motion is justified by their importance in fuel-saving and in the context of an eco-friendly design. However, a general lack of knowledge characterizes the phenomenon, since not even direct experience on the rolling tyre can reveal the insights of the correlated different dissipation effects, as the friction between the rubber and the road, the contact kinematics and dynamics, the tyre hysteretic behaviour and the grip. A new technology, based on fibre Bragg grating strain sensors and conceived within the OPTYRE project, is illustrated for the specific investigation of the tyre dissipation related phenomena. The remarkable power of this wireless optical system stands in the chance of directly accessing the behaviour of the inner tyre in terms of stresses when a real-condition-rolling is experimentally observed. The ad hoc developed tyre model has allowed the identification of the instant grip conditions, of the area of the contact patch and allows the estimation of the instant dissipated power, which is the focus of this paper.
Most damage-assessment strategies for dynamic systems only distinguish between undamaged and damaged conditions without recognizing the level or type of damage or considering unseen conditions. This paper proposes a novel framework for structural health monitoring (SHM) that combines supervised and unsupervised learning techniques to assess damage using a system’s structural response (e.g., the acceleration response of big infrastructures). The objective is to enhance the benefits of a supervised learning framework while addressing the challenges of working in an SHM context. The proposed framework uses a Linear Discriminant Analysis (LDA)/Probabilistic Linear Discriminant Analysis (PLDA) strategy that enables learning the distributions of known classes and the performance of probabilistic estimations on new incoming data. The methodology is developed and proposed in two versions. The first version is used in the context of controlled, conditioned monitoring or for post-damage assessment, while the second analyzes the single observational data. Both strategies are built in an automatic framework able to classify known conditions and recognize unseen damage classes, which are then used to update the classification algorithm. The proposed framework’s effectiveness is first tested considering the acceleration response of a numerically simulated 12-degree-of-freedom system. Then, the methodology’s practicality is validated further by adopting the experimental monitoring data of the benchmark study case of the Z24 bridge.
The present paper investigates a new paradigm to control a swarm of moving individual vehicles, based on the introduction of a few random long-range communications in a queue dominated by short-range car-following dynamics. The theoretical approach adapts the small-world theory, originally proposed in social sciences, to the investigation of these networks. It is shown that the controlled system exhibits properties of higher synchronization and robustness with respect to communication failures. The considered application to a vehicle swarm shows how safety and security of the related traffic dynamics are strongly increased, diminishing the collision probability even in the presence of a hacker attack to some connectivity channels.
This paper presents a comprehensive analysis of the indirect control of inertial properties of a rigid bodies system by semi-actively modifying the viscosity of tunable dampers. Linear Quadratic Regulator (LQR) optimal control logic and Hilbert-Huang Transform (HHT) analysis are employed to investigate its impact on the system response. The study utilizes a simple 2-d.o.f. architecture, referred to as the Toy Model, to demonstrate how proper selection of the damping coefficient allows for manipulation of the equivalent mass and variation of the natural frequency within a specific resonant band. Chirp excitations are applied to the Toy Model, and an iterative LQR scheme is implemented to optimally control the damping coefficient, thereby preventing resonance. Given that the adoption of the semi-active controller significantly alters the primary mass response, it is crucial to establish the cause-and-effect relationship between the control law and system response, which is achieved through the HHT. Notably, the proposed model is the first known example of a physical system that exhibits both intra- and inter-wave modulations of the instantaneous frequency of the main mass response, leading to a meta-phenomenon here defined as meta-frequency modulation. This meta-frequency modulation nonlinearly distorts the response of the optimally controlled system compared to passive optimization.