Epoxy/silica thermosets with tunable matrix (vitrimers) were prepared by thermal curing of diglycidyl ether of bisphenol A (DGEBA) in the presence of a hardener—4-methylhexahydrophthalic anhydride (MHHPA), a transesterification catalyst—zinc acetylacetonate (ZAA), and 10–15 nm spherical silica nanoparticles. The properties of the resulting material were studied by tensile testing, thermomechanical and dynamic mechanical analysis. It is shown that at room temperature the introduction of 5–10 wt% of silica nanoparticles in the vitrimer matrix strengthens the material leading to the increase of the elastic modulus by 44% and the tensile stress by 25%. Simultaneously, nanoparticles enhance the dimensional stability of the material since they reduce the coefficient of thermal expansion. At the same time, the transesterification catalyst provides the thermoset with the welding ability at heating, when the chain exchange reactions are accelerated. For the first time, it was shown that the silica nanoparticles strengthen welding joints in vitrimers, which is extremely important, since it allows to repeatedly use products made of thermosets and heal defects in them. Such materials hold great promise for use in durable protective coatings, adhesives, sealants and many other applications.
The cure of an epoxy resin (3,4-epoxycyclohexylmethyl-3,4-epoxycyclohexane carboxylate) in the presence of silica nanoparticles modified by 3-(triethoxysilyl)propylsuccinic anhydride has been studied. Optimal conditions for the preparation of optically transparent polymer nanocomposites with increased glass transition temperatures are determined. The glass transition temperatures of the above nanocomposites are 50–70°C higher than those of the unfilled epoxy resin synthesized under the same conditions (100°C).
Epoxy matrices with a tunable matrix (vitrimers) are synthesized for the first time by curing a cycloaliphatic epoxy resin—3,4-epoxycyclohexylmethyl-3,4-epoxycyclohexane carboxylate—in the...
Thermoresponsive diblock copolymers of N-vinylcaprolactam (VCL) with N-vinylimidazole (NVI) have been synthesized for the first time through two-stage controlled reversible addition–fragmentation...
Three types of coatings (contact-based, release-based, and combined coatings with both contact-based and release-based actions) were prepared and tested for the ability to inactivate SARS-CoV-2. In these coatings, quaternary ammonium surfactants were used as active agents since quaternary ammonium compounds are some of the most commonly used disinfectants. To provide contact-based action, the glass and silicon surfaces with covalently attached quaternary ammonium cationic surfactant were prepared using a dimethyloctadecyl[3-(trimethoxysilyl)propyl]ammonium chloride modifier. Surface modification was confirmed by attenuated total reflection infrared spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy, and contact angle measurements. The grafting density of the modifier was estimated by XPS and elemental analysis. To provide release-based action, the widely used quaternary ammonium cationic disinfectant, benzalkonium chloride (BAC), and a newly synthesized cationic gemini surfactant, C18-4-C18, were bound non-covalently to the surface either through hydrophobic or electrostatic interactions. Virus titration revealed that the surfaces with combined contact-based and release-based action and the surfaces with only release-based action completely inactivate SARS-CoV-2. Coatings containing only covalently bound disinfectant are much less effective; they only provide up to 1.25 log10 reduction in the virus titer, probably because of the low disinfectant content in the surface monolayer. No pronounced differences in the activity between the flat and structured surfaces were observed for any of the coatings under study. Comparative studies of free and electrostatically bound disinfectants show that binding to the surface of nanoparticles diminishes the activity. These data indicate that SARS-CoV-2 is more sensitive to the free disinfectants.